for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Idle Adjusting Needle is the mixture-adjusting needle for the Zenith Stromberg CD175 constant-depression carburettor fitted to the Rover 3.5 V8. I...
View full detailsrear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8
Shim 1.65mm for Layshaft Speed - V8 4
Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...
View full detailsPiston ring set for the 3.5L Rover V8 petrol engine, supplied per piston. The rings seal the combustion chamber against the cylinder bore, transfe...
View full detailsDrive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.
Sealing Washer for the coolant temperature transmitter adaptor, for use on the 2.25L Diesel, 2.5L Diesel, and 2.5L Turbo Diesel engines. Fitted at...
View full detailsBulb is a 12V 21W single-filament bulb with a red finish, fitted in rear lamp assemblies. The single filament provides a single-intensity function...
View full detailsBlanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...
View full detailsSteel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.
Gasket
pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole
Female Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.
Thrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.
Bearing needle roller
Steel Road Wheel - 6.5J x 16, Wolf-style pattern. It provides the mounting surface for a tubeless road tyre and transfers vehicle load from the tyr...
View full detailsOuter Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...
View full detailsNeedle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...
View full detailsAlternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...
View full detailsConnecting Rod Bolt for the Rover 3.5L V8 petrol engine. The bolt clamps the connecting rod big-end cap to the rod, retaining the big-end bearing s...
View full detailsFuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...
View full detailsOil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...
View full detailsbush shock absorber OEM, bush anti roll bar OEM
Conrod bearing set .030"" KING
Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate
Rear Window Glass for the rear door, part of the rear door glazing. Heated glass with an integral electric demist element and a Sundym solar tint, ...
View full detailsRear Quarter Window Glass in clear (untinted) glass for the rear body side. It fits the quarter window aperture in the rear body, located alongsid...
View full detailsDifferential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...
View full detailsSide Lamp Lens, the late 'fish-eye' front type for military-specification side lamps. The lens fits the front side lamp body to seal the bulb apert...
View full detailsFront Housing Gasket for the LT95 four-speed gearbox fitted to V8 engines. It seals the joint between the gearbox front housing and the main casin...
View full detailsDifferential Pinion Shim - 0.062" selective shim used to set the pinion position within the differential (final drive) assembly. Fitted at the pin...
View full detailsDifferential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...
View full detailsSupport Bracket for the upper rear body section, forming part of the rear body-to-chassis structure. It locates and supports the upper rear body p...
View full detailsScrew securing the front catch of the rear side sliding window. Used to fix the sliding window catch on Station Wagon bodies of early Series models.
Piston Ring Set in standard size, for the 2.25L and 2.5L naturally aspirated four-cylinder diesel engines running standard-size pistons in an unbor...
View full detailsBearing layshaft LT95 4-speed manual gearbox for Rover 3.5L V8 - S3 109" Stage One V8 - early 110" V8 (Stage Two) - 101" Forward Control - Classic...
View full detailsCarburettor Gasket sealing the inlet manifold adaptor elbow to the carburettor on the Rover V8 twin-carburettor petrol engine. Fitted between the ...
View full detailso-ring sealing shaft reverse gear LT95 4-speed - S3 109" stage one V8 - 110" V8 4-speed manual - RRclassic 4- speed manual - 101" Forward Control
set screw M6 x 25mm 8.8 various applications
Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...
View full detailsScrew, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...
View full detailsThrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...
View full detailsSteel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...
View full detailsWoodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...
View full detailsBody Corner Capping, right-hand, galvanised steel. The protective capping that covers the rear corner of the body where the side and rear panels me...
View full detailsWoodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.
Restore the structural integrity of your Defender 90/110 or Series SWB/LWB with this right-hand side (RHS) bulkhead repair panel, designed for dura...
View full detailsRepair and restore the bulkhead structure of your Defender 90/110 or Series SWB/LWB with this left-hand side (LHS) bulkhead repair panel, designed ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →