for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Starter Solenoid Solenoid for the Lucas 3M100 starter motor on the 3.5L V8 petrol engine. Mounted on the starter motor body, it engages the starte...
View full detailsLockable Cubby Box is a centre-console storage box that mounts on the transmission tunnel between the front seats, providing a secure enclosed comp...
View full detailsFloor Mat for the second seat row, a ribbed rubber mat protecting the intermediate floor area. Approximate dimensions 1490 x 460 x 3 mm.
Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...
View full detailsFuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...
View full detailsSelector Cover Gasket - LT95
Oil Pump Gasket for the LT95 four-speed gearbox. It seals the oil pump to the gearbox casing on the LT95 transmission, used behind the Rover V8 an...
View full detailsUpgrade your vehicle's lighting with these 8-inch black halogen driving lights. High power 100W lamps with universal fitting, plastic stone guards,...
View full detailsPiston for the 2.25L 4-cylinder diesel engine, machined to +0.040" oversize for a rebored cylinder block. The piston transfers combustion pressure...
View full detailsStarter Solenoid - the solenoid for the Lucas M113 starter motor, part of the engine starting system. Mounted on the starter motor body, the solen...
View full detailsFront Lamp Guards - protective guards that fit over the front lamps to shield the lenses from stones, branches and impact damage. The guards are hi...
View full detailsPlain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.
rings piston set per piston petr 2.25 +.020" os replacement per zuiger
Floor Mat Retainer secures the intermediate second-row rubber floor mat. Holds the mat in position against movement underfoot.
Tailgate Hinge Bolt secures the tailgate hinge to the rear body in the tailgate hinge assembly. Used on High Capacity Pick Up (HCPU) body configur...
View full detailsRocker Cover for the 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. It encloses the rocker gear at the top of the cylinder head an...
View full detailsAxle Shim for the Salisbury rear differential, 0.003" thickness. This imperial-dimension shim is used during differential overhaul to set pinion s...
View full detailsBrake Lining Set for the rear drum brake assembly. This set contains the friction linings for both rear brake shoes, forming the braking surface b...
View full detailsFront Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...
View full detailsHook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.
Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...
View full detailsSalisbury Axle Shim used in the differential assembly of the Salisbury rear axle. This shim is positioned against the inner pinion shaft bearing a...
View full detailsPiston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...
View full detailsBolt securing the exhaust manifold on the Rover V8 petrol engine. A 3/8" UNC x 1 1/8" fastener used to retain the exhaust manifold to the cylinder...
View full detailsStatic Lap Belt - a two-point lap seat belt for a centre or side-facing seating position. The webbing is a fixed length and is adjusted by hand to...
View full detailsDistributor Coupling - drive coupling for the distributor. Transmits drive to the distributor shaft on the 2.25L and 2.5L petrol engines.
Cylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...
View full detailsSpare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...
View full detailsInlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...
View full detailsGlass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.
Roller Fairlead - zinc coated - for steel cable winches. This four-roller fairlead mounts to the front of a winch bumper and guides the steel cabl...
View full details3 man seat Techno Exmoor trim EX4188 EXT006-TC
Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...
View full detailsSteel Road Wheel, 5.5J x 16, of welded construction for tube-type tyre fitment. The rim is designed to run with an inner tube rather than a tubele...
View full detailsRubber Mat - a heavy-duty 6mm rubber floor mat for the rear load area of hardtop models. Laid over the load-area floor, the 6mm rubber protects th...
View full detailsPortable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...
View full detailsFront Hazard Light Wiring Harness is a section of the front lighting wiring loom that carries the supply and switching feeds to the front hazard an...
View full detailsDifferential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...
View full detailsBumper top SIII/90/110
Spare Wheel Carrier Spacer for the rear-door mounted spare wheel carrier. It spaces the spare wheel carrier stud mounting on the rear door, settin...
View full detailsRear Wing Protector - a protective panel fitted over the rear wing to shield the bodywork from scratches, denting and wear during loading and off-r...
View full detailsRear Lamp Guards - a set of four steel guards fitted over the rear lamp assemblies to protect the lenses and lamp bodies from stone chips, branch s...
View full detailsSpecial Bolt
Clutch Lever Pivot Pin for the LT76 gearbox bellhousing. It forms the pivot about which the clutch release lever rotates when the clutch pedal is o...
View full detailsSide Frame Assembly Kit - left-hand side - is a full body side frame for four/five-door Station Wagon bodywork, used to restore or replace a corrod...
View full detailsSide Frame Assembly Kit - right-hand side - is a full body side frame for four/five-door Station Wagon bodywork, used to restore or replace a corro...
View full detailsRoof Light Bar is a straight tubular steel mounting bar that attaches to the vehicle's roof rain gutters. The bar features four lamp mounting brac...
View full detailsManifold Stud is an M8 x 65 mm threaded stud that secures the inlet and exhaust manifold to the cylinder head on the four-cylinder petrol engine. ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →