for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Exhaust Rocker Valve for Land Rover diesel engines. This valve is located in the cylinder head and controls the exhaust port opening and closing c...
View full detailsInjection Pump for the 2.25L four-cylinder diesel fuel system. It meters pressurised fuel and delivers it to the injectors in firing sequence, gove...
View full detailsCamshaft Retaining Plate for the four-cylinder engine. Bolted to the front face of the cylinder block behind the camshaft gear, it locates the cams...
View full detailsUpgrade the cooling system of your Series 2, Series 2A, or Series 3 Land Rover with this Revotec Cooling Kit. This kit includes a 14" high-power bl...
View full detailsLimited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...
View full detailsRoof Access Ladder - a bolt-on ladder for reaching the roof and roof rack, mounted on the left-hand side of the body. It clamps to the rain gutter...
View full detailsExtended Bulkhead Upper Repair Panel Set restores the upper section of the bulkhead, the structural firewall panel that separates the engine bay fr...
View full detailsRestore your Series 3 Land Rover with this brand-new bulkhead, designed for universal fitment to both Left-Hand Drive (LHD) and Right-Hand Drive (R...
View full detailsBoss Kit designed for 36 splines and a 16mm shaft. Compatible with Defender models from 1A onwards up to HA, this kit is drilled and features a con...
View full detailsBulkhead Repair Panel with Vents - Left-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent sur...
View full detailsSliding Window Kit - a pair of sliding side windows fitted with green-tinted toughened glass certified to E11 CE R-43. The sliding panes provide op...
View full detailsRear Door Goal Post Cladding - Safari is a three-piece exterior trim set for the rear door goal-post surround. It clads the upper goal-post and pi...
View full detailsSeat Belt Anchorage Frame is a front seat belt mounting bar for Soft Top vehicles, providing secure anchorage points where the open body offers no ...
View full detailsCarburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...
View full detailsTowing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...
View full detailsTowing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...
View full detailsCubby Box - a centre console storage box that mounts on the transmission tunnel between the front seats. The body is finished in grey with a vinyl...
View full detailsC-Post Bottom Leg Repair Panel - Right Hand is a weld-in body repair section for the lower leg of the C-post, the rearmost body pillar of the Stati...
View full detailsC-Post Bottom Leg Repair Panel - Left Hand is a weld-in body repair section for the lower leg of the C-post, the rearmost body pillar of the Statio...
View full detailsCapture the sleek design of the Range Rover Evoque with this premium 1:76 scale diecast model in elegant Baltic Blue. This detailed replica perfect...
View full detailsLED Light Kit - a Wipac clear-lens LED lamp set that replaces the standard 73 mm exterior lamps with LED units. The kit contains eight lamps plus ...
View full detailsDoor Mirror - complete exterior door mirror for rearward vision. It fits to the door-mounted mirror arm and carries a convex polycarbonate lens (2...
View full detailsSteel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).
Bolt - 1/2 UNF x 4.5. Hexagon-head threaded fastener, 1/2 inch UNF thread by 4.5 inch length, used on military-specification chassis and body appl...
View full detailsBolt - M6 metric thread, 70 mm long. A threaded fastener for securing components at a bolted joint. Tightened to the torque specified for the asse...
View full detailsBumper End Plate Protector Pair - protection plates that fit over the outer ends of the front bumper. Supplied as a left- and right-hand pair, the...
View full detailsRear Rubber Mat for the rear floor and load area, cut to suit short-wheelbase County-specification vehicles. The moulded rubber mat protects the r...
View full detailsRear Wing Protector - a protective panel fitted over the rear wing to shield the bodywork from scratches, denting and wear during loading and off-r...
View full detailsLED Direction Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It uses an L...
View full detailsDirection Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It is supplied a...
View full detailsReinforcement is a structural stiffener for the lower rear body. It fits to the lower section of the rear body structure to add rigidity to the sur...
View full detailsPropshaft Universal Joint for V8 driveline applications. The universal joint lets the propeller shaft transmit drive through the changing angle be...
View full detailsDiaphragm assembly VAC
Circlip
Starter Motor for the 2.25L petrol engine, 24V system - part of the engine starting circuit. On cranking, the motor's pinion engages the flywheel ...
View full detailsDrive Screw retaining the direction-indicator switch clamp. A hammer-drive screw used to secure the indicator switch clamp, and the indicator cowl...
View full detailsDifferential Cross Shaft for the Land Rover-type differential. The cross shaft locates through the differential case and carries the two differenti...
View full detailsBall Joint
Stop Cable Diesel Without Steering Column Lock RHD
Drop Arm for the manual steering box. The drop arm splines onto the steering box rocker shaft and converts the box's rotary output into the fore-an...
View full detailsHeater Tap Adaptor for the heater control circuit. This zinc-plated mild steel adaptor forms the threaded interface between the heater water valve ...
View full detailsNeedle Roller Bearing
Primary Pinion Shim - 2.15 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...
View full detailsSpacer
Low Range Gear
Brake Drum - 10 Inch for the wheel brake assembly on early short wheelbase Series Land Rovers. Fits the 10-inch drum brake system used on SWB (88"...
View full detailsRear Halfshaft for the Salisbury rear axle, 24-spline, left-hand side. The halfshaft transmits drive from the differential through the axle casing...
View full detailsLocation Pin
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →