for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Rear Stop/Tail Lamp - LED - LED combined stop and tail lamp with a red lens, supplied as a complete sealed unit to replace the standard rear stop/t...
View full details7" round LED headlamp 12/24V chrome 78W LHD (pair)
Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...
View full detailsHead Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...
View full detailsCrankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...
View full detailsHeadlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...
View full detailsHead Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...
View full detailsSedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...
View full detailsBolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...
View full detailsBrake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...
View full detailsClutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...
View full detailsInlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...
View full detailsGearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...
View full detailsCoolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...
View full detailsExpansion Tank Cap seals the cooling system expansion (header) tank. The plastic cap closes the tank and holds the coolant circuit at its rated pr...
View full detailsDipstick Tube for the 2.25L four-cylinder petrol and diesel engines in the Series range. The tube fits into the cylinder block and guides the oil ...
View full detailsO-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...
View full detailsSwivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...
View full detailsSwivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...
View full detailsLocking plate
Steering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...
View full detailsHex Head Bolt with a 1/4" BSF thread and a 5/8" shank length. A common application is the swivel pin housing, where it retains the swivel oil seal...
View full detailsExhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...
View full detailsDrive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...
View full detailsHub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...
View full detailsLokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...
View full detailsLED Light Kit - 73mm
Inlet Valve Stem Seal for the cylinder head valvetrain, fitted over the inlet valve stem at the top of the valve guide. The seal meters the oil pa...
View full detailsSpare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...
View full detailsOil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...
View full detailsHex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...
View full detailsFront Side Lamp with a clear lens and LED illumination, mounting in the front lighting position to serve as the side (parking) light. The LED draw...
View full detailsIgnition Switch - Diesel - Switch Only is the electrical switch element of the ignition system for diesel applications. It supplies the rotary swi...
View full detailsTemperature transmitter
Seal
Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...
View full detailsGlow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...
View full detailsSeat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...
View full detailsWindscreen Seal - 2.5m is the rubber glazing seal for the windscreen, supplied as a 2.5 m length. It seats the windscreen glass in its aperture an...
View full detailsHeater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...
View full detailsHeadlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...
View full detailsOil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...
View full detailsSplit Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...
View full detailsMounting Stud
Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...
View full detailsFlywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...
View full detailsLamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...
View full detailsSpring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →