for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...
View full detailsRestore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...
View full detailsBrake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...
View full detailsPower Steering Pressure Hose - LHD for the power steering hydraulic circuit. This high-pressure hose connects the power steering pump outlet to th...
View full detailsRear Reverse Lamp - reversing lamp for the rear lighting assembly, providing white illumination to the rear when reverse gear is selected. It moun...
View full detailsTrack Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...
View full detailsExhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...
View full detailsShock Absorber Bush for the lower mounting of a suspension damper. The rubber bush seats in the shock absorber's lower mounting eye, locating the ...
View full detailsDoor Casing Trim Clip is a fir-tree push-fit fastener used in the interior door trim assembly to retain the door casing panel against the door fram...
View full detailsGearbox Mount, right-hand side. Part of the transmission mounting assembly. The mount sits between the gearbox and transfer box casing and the cha...
View full detailsExhaust rear silencer 90
Brake Pad Retention Kit - front brake pad retaining hardware for the disc brake assembly. Secures the front brake pads in the caliper on installat...
View full detailsIgnition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...
View full detailsSide Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...
View full detailsIgnition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...
View full detailsRear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...
View full detailsRadius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...
View full detailsNut - a plain full hex nut with a 3/8" BSF (British Standard Fine) thread. A general-purpose imperial fastener used at many points across the engi...
View full detailsLower Windscreen Seal for the Defender windscreen mounting assembly. This felt seal spans the full width of the lower windscreen channel, sealing ...
View full detailsLower Swivel Pin for the front axle swivel housing assembly. The lower swivel pin provides the lower pivot point for the steering knuckle, working...
View full detailsFelt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...
View full detailsDrive Belt Tensioner for the 2.5L Td5 5-cylinder turbo diesel engine. The tensioner is listed in the Land Rover parts catalogue in the Td5 drive b...
View full detailsCylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...
View full detailsCoolant Bypass Hose for the 4-cylinder petrol and naturally-aspirated diesel engines (non-TDi). It forms the bypass path of the engine cooling cir...
View full detailsHydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...
View full detailsFront Seat Belt Assembly - right-hand inertia reel unit in the occupant restraint system. Installed at the front right-hand seating position, it p...
View full detailsPower Steering Pump is the engine-driven hydraulic pump at the heart of the power-assisted steering circuit on the 300 TDi 2.5L turbo diesel. Belt...
View full detailsAnchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...
View full detailsFuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...
View full detailsClutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...
View full detailsHandbrake Gasket for the transmission handbrake (parking brake) assembly, sealing the mud shield (oil catcher) against the brake back plate. It ke...
View full detailsBrake Shoe Return Spring for the rear drum brake assembly, fitted at the upper end of the brake shoes adjacent to the wheel cylinder. The spring h...
View full detailsDifferential flange 4-spline
Drain Plug Removal Tool for slackening and refitting the square-recess oil drain plugs fitted to Land Rover axles, gearboxes and engine sumps. The...
View full detailsOil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...
View full detailsHub Nut Socket is a 52mm deep impact socket with a 1/2" square drive, used to remove and refit the hub retaining nut on the wheel bearing assembly....
View full detailsFlanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...
View full detailsRear Mudflap for the right-hand side, supplied with its mounting bracket. It forms part of the exterior body protection, fitting behind the rear wh...
View full detailsBonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...
View full detailsCylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...
View full detailsRear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...
View full detailsNAS Link Lead Extension – a three-wire extension link loom for the rear lighting circuit. It connects the rear stop/tail lamp to the vehicle body ...
View full detailsUniversal Joint for the axle half shaft, allowing the shaft to transmit drive through an angle. The joint sits within the half shaft and lets it t...
View full detailsSpeedometer Cable connects the speedometer drive on the gearbox to the speedometer head in the instrument cluster. The rotating inner cable transm...
View full detailsSwitch indicator Defender to GA455945 replacement
Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...
View full detailsNyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...
View full detailsFront Bumper for the front-end body structure, finished in black. The bumper mounts across the front of the chassis to form the front impact face ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →