for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Upgrade your vehicle's lighting with these 8-inch black halogen driving lights. High power 100W lamps with universal fitting, plastic stone guards,...
View full detailsGlow Plug - heater plug for the pre-heat (cold-start) circuit of the 2.5L diesel engine. It threads into the cylinder head so its heating element ...
View full detailsWindscreen hinge for the right-hand side. One of the pair of hinge brackets that carry the windscreen frame at its lower corners, bolting the frame...
View full detailsPiston Ring Set for the 2.5 litre four-cylinder naturally aspirated diesel engine, standard bore size. The rings seal the combustion chamber again...
View full detailsTorx Pan-Head Screw, M5 x 25. Secures the radiator grille and rear end door casing trim.
Heater Cable Clip retains the heater and air-conditioning control cable within the HVAC control assembly, holding the cable on its correct routing.
Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...
View full detailsPiston for the 2.25L 4-cylinder diesel engine, machined to +0.040" oversize for a rebored cylinder block. The piston transfers combustion pressure...
View full detailsCondenser mounts within the distributor as part of the ignition system. It suppresses arcing across the contact breaker points as they open, prote...
View full detailsSunroof Finisher is a trim finisher for the sunroof assembly. It frames the edge of the sunroof aperture, concealing the join between the sunroof ...
View full detailsPiston Ring Set for a single piston, in 0.020-inch oversize. The set provides the compression and oil-control rings for one piston and is machined...
View full detailsDifferential Bearing Shim - 0.063in
Shock Absorber - front gas-charged suspension damper. Mounted between the front axle and the chassis, it damps spring oscillation to control body ...
View full detailsCapping assembly body side Station wagon 110"" RH, one piece, black
Exhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.
Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...
View full detailsScrew used as a body and underbody fixing across several assemblies, including the tailboard striker, the folding side-door step assembly, and the ...
View full detailsPlate Nut - RH for the front door latch striker on the Defender. The plate nut is fixed to the door pillar on the right-hand side and provides the...
View full detailsAlternator for the 2.4L Duratorq TD4 four-cylinder turbo diesel charging system, rated at 150 amp output. Belt-driven from the crankshaft pulley, ...
View full detailsFiller Strip for the fixed side window aperture, part of the body glazing assembly. The strip fills and finishes the gap around the fixed side win...
View full detailsA-Post Finisher is the trim cover for the right-hand A-post, the windscreen pillar, concealing the pillar structure and dressing the join between t...
View full detailsAir Intake Grille for the wing-top fresh air intake, left-hand side. Mounted on top of the front wing, the moulded grille covers the plenum intake...
View full detailsGearbox Retainer - LT77
Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...
View full detailsFinger Pull for the side door sliding glass window. The outer grip fitted to the sliding glass pane, used to slide the window open and closed.
Rear Seat Belt Buckle for the rear occupant restraint system. This is the receiving buckle stalk into which the seat belt tongue latches, securing...
View full detailsRear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...
View full detailsSelf-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...
View full detailsFusebox Label is the printed identification label for the main fuse box. It maps each fuse position to its circuit and rating, allowing the correc...
View full detailsCork Washer for the auxiliary (extra) fuel tank in the fuel system. The cork washer forms a fuel-resistant seal at a tank fitting, compressing on ...
View full detailsWing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...
View full detailsA/C O-Ring - the front pipe sealing O-ring for the manual air conditioning system. It seals the refrigerant pipe joint on the front line running b...
View full detailsStarter Solenoid - the solenoid for the Lucas M113 starter motor, part of the engine starting system. Mounted on the starter motor body, the solen...
View full detailsWindow Regulator Handle Adaptor for the front door glass and window regulator assembly. The adaptor couples the manual window winder handle to the...
View full detailsMainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...
View full detailsPower Steering Hose is a flexible hydraulic hose in the power steering circuit. It carries pressurised hydraulic fluid through the steering system...
View full detailsPower Assisted Steering Hose for the hydraulic power steering circuit, specific to left-hand drive applications. This pipe forms the return leg of...
View full detailsNeedle Roller Bearing supports the fifth-speed gear on the mainshaft of the LT85 five-speed manual gearbox. The caged needle rollers let the fifth...
View full detailsOil Filter Housing Adaptor - part of the oil filter and oil cooler assembly. It mounts on the oil filter housing and provides the connection betwee...
View full detailsscew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)
Front Lamp Guards - protective guards that fit over the front lamps to shield the lenses from stones, branches and impact damage. The guards are hi...
View full detailsBlanking Plug used to close an unused aperture in body and trim panels. Seals openings such as seat base fitting holes and redundant grommet posit...
View full details"Td5" Decal - black engine-designation decal, approximately 13 cm, identifying the Td5 diesel engine variant. Applied to the exterior body as an e...
View full detailsFuel Pipe for the fuel delivery system on the 2.5-litre four-cylinder diesel engine, routing fuel along the supply line towards the injection pump....
View full detailsExhaust Manifold Heat Shield mounts over the exhaust manifold to protect surrounding components from radiant heat. It deflects heat away from adja...
View full detailsBrake Hose Kit - non-ABS. A set of flexible brake hoses that connect the rigid brake pipes on the chassis to the moving calipers and rear axle. Th...
View full detailsVacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...
View full detailsDowel for the manual gearbox gear-selector assembly. It locates the selector components against the housing to hold their alignment during gear eng...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →