for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
The Spring Seat Front RHS is an essential suspension component designed for the Defender 90, Defender 110, and Defender 130 models. This part ensur...
View full detailsFront Chassis Leg is the forward structural section of the chassis frame on the left-hand side, also known as the front dumb iron. It carries the ...
View full detailsFront Chassis Leg is the forward structural section of the chassis frame on the right-hand side, also known as the front dumb iron. It carries the...
View full detailsFront Seat Spring - Left-Hand, forming part of the front seat base assembly. This spring sits within the seat base structure on the left-hand fron...
View full detailsRear Radius Arm Mount is the chassis bracket that anchors the rear trailing link to the chassis on the left-hand side. The trailing link controls ...
View full detailsFront Radius Arm Mount is the chassis bracket that anchors the front radius arm to the chassis on the left-hand side. The radius arm controls fore...
View full detailsSynchro Unit - the 1st/2nd gear synchromesh assembly carried on the mainshaft of the LT77 five-speed manual gearbox. The synchro hub is splined to...
View full detailsDifferential Gear Kit is a set of differential gears for the Rover-type axle differential, in the 10-spline configuration. The differential gears ...
View full detailsWaterproof seat cover for a single outer front seat, finished in grey. The cover is shaped to the standard seat frame and fits over the existing u...
View full detailsHeadlamp Guard in clear acrylic, fitting over the headlamp to shield the lens from stones, branches and debris thrown up during off-road and rough-...
View full detailsDog Guard for the Station Wagon, forming a full-height barrier between the rear load area and the passenger cabin to restrain animals or loose carg...
View full detailsFront Door Assembly - Lift Up - LH Complete left-hand front door assembly for the bodyside, built for the early lift-up exterior handle arrangement...
View full detailsDoor Assembly - Front - RH - Lift Handle Complete right-hand front door assembly for the bodyside, built for the early lift-up exterior handle arra...
View full detailsProtector Lamp
Kit repair brake master cylinder OEM
Stripped Engine Unit for the 2.5L 300 TDi four-cylinder turbo diesel – the reconditioned core mechanical assembly of the engine. Supplied in strip...
View full detailsRear Wiper Arm Kit for the rear screen (backlight) wiper system. The arm fits the rear wiper motor spindle and sweeps the blade across the rear sc...
View full detailsHandbrake Return Spring for the rod-operated transmission parking brake on the LT230 transfer box, in the horizontally mounted shoe arrangement. T...
View full detailsBrake Caliper Piston with a stainless steel body for the hydraulic disc brake caliper, 46mm diameter and 30.68mm height. The piston sits within th...
View full detailsWater Pump for the engine cooling circuit, belt-driven from the front of the engine. The pump circulates coolant through the cylinder block, heads...
View full detailsMain Bearing Set - V8 - Standard is the set of crankshaft main bearing shells that carry the crankshaft in the V8 cylinder block, in standard size....
View full detailsTailgate Assembly — the rear load door of the body, providing access to the load space. Supplied in the configuration without a spare wheel carrie...
View full detailsExhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...
View full detailsInlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...
View full detailsPiston Assembly for the 2.5L 200 TDi turbo diesel, forming part of the piston and connecting-rod assembly within the cylinder block. The piston tr...
View full detailsABS Sensor Kit - Rear is part of the four-wheel anti-lock braking system, fitted at the rear axle. Each sensor monitors wheel rotational speed and...
View full detailsFront Brake Hose is the flexible hydraulic hose in the front braking circuit, connecting the rigid brake line on the chassis to the front brake cal...
View full detailsFront Brake Hose is the flexible hydraulic hose in the front braking circuit, connecting the rigid brake line on the chassis to the front brake cal...
View full detailsBolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor
Rear Premium Ceramic Brake Pads for 110/130
Hex Nut
Rear Floor Mat Set is a drop-in moulded rubber mat set for the rear floor area. The mats locate over the rear footwell and floor pan to protect th...
View full detailsHalf Shaft - LH (Left-Hand), part of the Rear Axle Drive Assembly on the Defender 90, 110, and 130. This half shaft transmits drive torque from th...
View full detailsFelt Pad for the side and sliding window glass. A felt anti-noise pad that seats against the window glass to cushion it within its channel, dampin...
View full detailsPiston Assembly for the 2.5 four-cylinder naturally aspirated diesel, standard size. The piston transfers combustion pressure to the connecting ro...
View full detailsPiston - 2.5L N/A Diesel - 0.020" Oversize for the Defender fitted with the 2.5L naturally-aspirated diesel engine, for use during engine overhaul ...
View full detailsFront Outer Wing is the left-hand (nearside) bolt-on steel body panel covering the front wheelarch and running back from the headlamp panel to the ...
View full detailsRear Door - the rear load (tail) door that closes the back of the body. Supplied unglazed, the door is pre-drilled with mounting holes to accept a...
View full detailsFront Outer Wing is the right-hand (offside) bolt-on steel body panel covering the front wheelarch and running back from the headlamp panel to the ...
View full detailsPiston Ring Kit
Carburettor Overhaul Kit - service kit for the Weber twin-choke carburettor fitted to the 2.25L and 2.5L four-cylinder petrol engines. The kit is ...
View full detailsSealing Washer - bonded (Dowty-type) seal for the power steering pump banjo union. The washer is a metal outer ring with a vulcanised elastomeric ...
View full detailsBanjo Union - the hollow banjo bolt that secures the high-pressure feed hose to the power steering pump outlet. It passes through the eye of the h...
View full detailsRegulator & Brush Assembly - the combined voltage regulator and brush box fitted to Lucas alternators in the charging circuit. The unit mounts...
View full detailsStartermotor 2,5 diesel NEW
Ignition Solenoid - 2.5L Petrol
Circlip for the front driveshaft CV joint on Defender models to 1993. This circlip retains the CV joint on the front driveshaft, securing it withi...
View full detailsFront Bumperette - a compact protection unit fitted at the front of the vehicle. It provides localised impact protection to the front end. Manufac...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →