for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Fuel Cap seals the fuel filler neck, closing the fuel system to keep out dirt and water and to contain fuel vapour. Vented, non-locking type in bl...
View full detailsTop radiator hose from the engine cooling circuit, connecting the thermostat housing outlet at the top of the engine to the radiator top inlet. It...
View full detailsRear Exhaust Silencer sits at the back of the exhaust system, providing the final stage of noise reduction before gases leave at the tailpipe. Int...
View full detailsRear Silencer & Tailpipe - Stainless - the rear section of the exhaust system, combining the rear silencer and tailpipe in a single assembly, c...
View full detailsCentre Exhaust Silencer sits in the middle section of the exhaust system, reducing noise as gases pass from the front pipe rearward toward the tail...
View full detailsFuel Spill Pipe from the fuel tank and pump mounting assembly, used on petrol applications. The spill (return) pipe carries the fuel not consumed ...
View full detailsExhaust Downpipe for the 2.25L 4-cylinder petrol engine. The downpipe is the first section of the exhaust system. It bolts to the exhaust manifold...
View full detailsFoam Dunlop Washer
PDWA Valve (Pressure Differential Warning Actuator) for the brake hydraulic circuit. This valve connects the front and rear brake circuits and mon...
View full detailsAccelerator Pedal is the driver's throttle input, mounted in the cab footwell against the bulkhead. The pedal pivots on its bracket and operates t...
View full detailsHand Throttle Grommet fits into the hand throttle control assembly, lining the aperture where the throttle cable passes through and sealing it agai...
View full detailsExhaust Clamp Plate for the front exhaust pipe mounting. The plate clamps the front section of the exhaust at its mounting point, holding the pipe...
View full detailsHeater Hose connecting the heater to the engine coolant pipe, part of the heater pipes and hoses assembly. The hose forms part of the coolant path...
View full detailsHeater Hose connecting the heater to the engine coolant pipe, part of the heater pipes and hoses assembly. The hose forms part of the coolant path...
View full detailsHeater Hose for the cabin heating circuit, carrying engine coolant between the cooling system and the heater matrix to supply heat to the cabin. S...
View full detailsHeater Hose running to the heater, part of the heater pipes and hoses assembly. The hose carries engine coolant to the heater matrix, where cabin ...
View full detailsLower Radiator Hose in the engine cooling circuit, carrying coolant from the radiator bottom outlet to the water pump inlet. Moulded rubber hose f...
View full detailsCoolant Hose for the engine cooling circuit of the 2.5L Naturally Aspirated Diesel engine. This hose carries coolant between the engine block and ...
View full detailsGalvanised Chassis - complete replacement chassis frame for 88" short-wheelbase vehicles. Fully galvanised as standard, giving corrosion protectio...
View full detailsChassis - 109" Station Wagon - Galvanised is a full replacement chassis frame for the long-wheelbase Station Wagon. The galvanised finish provides...
View full detailsAccelerator Cable Dutch Lightweight Diesel
Front exhaust downpipe, right-hand side, for the V8 exhaust system. The downpipe bolts to the right-hand exhaust manifold flange and carries the e...
View full detailsEngine Mounting is a rubber-to-metal anti-vibration mount in the engine mounting assembly, supporting the petrol engine on the chassis frame. The ...
View full detailsTow Hitch - NATO Pintle is a rotating military-pattern towing hook that mounts directly through the rear crossmember. The pintle rotates to allow ...
View full detailsDoor Hinge is the upper front door hinge for the right-hand side, part of the front door mounting assembly. It bolts to the body pillar and to the...
View full detailsDrain Channel - Rear Side Door installed vertically within the rear side door frame, channelling water away from the fixed quarter light aperture a...
View full detailsChannel fitted to the top of the Defender rear side door frame, guiding and retaining the upper edge of the main drop glass as it operates.
Seat Belt Assembly Rear Centre Lap
Body Seal for the upper left-hand side panel of the rear body, sealing the joint between the upper side panel and the hard top. It closes the gap ...
View full detailsGlazing Strip
Rear Quarter Glass is a fixed side glazing panel that sits in the rear body quarter, forming the glazed opening behind the rear side door. It loca...
View full detailsCapping - LH is the top capping panel for the left-hand rear corner of the body. This pressed steel capping closes the upper edge of the rear corn...
View full detailsRear Body Capping is the capping strip fitted along the top edge of the rear body side, covering and protecting the exposed panel edge and giving t...
View full detailsA-Post Trim is the interior trim panel that covers the A-pillar (the windscreen pillar), concealing the body structure and any wiring routed throug...
View full detailsSeat Mounting Bracket is the structural mounting point that locates and supports the rear forward-facing split seat, securing the seat base to the ...
View full detailsSeat Mounting Bracket is the structural mounting point that locates and supports the rear forward-facing split seat, securing the seat base to the ...
View full detailsStiffener
Bonnet Reinforcement - Spare Wheel Ring is a structural reinforcing ring fitted to the bonnet to support a bonnet-mounted spare wheel. It spreads ...
View full detailsDoor Check Strap Channel is the channel of the front door check strap (checker) assembly. It guides and retains the check strap as the door swings,...
View full detailsScrew used as a fixing throughout the door hardware assemblies. Four secure the front door latch mechanism; the same screw is specified for the rea...
View full detailsClip
Window Regulator - the lift mechanism that raises and lowers the rear side door glass. It mounts inside the door and carries the glass in a guide c...
View full detailsFront Door Striker - the striker that the front door latch engages to hold the door closed. It fixes to the body pillar and provides the catch poi...
View full detailsBonnet Spare Wheel Support Plate - a reinforced plate that forms the mounting base for a bonnet-mounted spare wheel. It fixes to the bonnet panel ...
View full detailsSpare Wheel Carrier U-Bolt - a U-shaped clamping bolt that secures the spare wheel carrier to the rear door. It passes around the carrier mounting...
View full detailsRear Mudflap >AA - 90 - LH
Door Check Strap Link - left-hand front door check link, round type. The check link connects the door to the body pillar and limits the door's ope...
View full detailsAshtray Retainer - mounting bracket that secures the ashtray assembly into the upper dashboard crash pad. It locates and holds the ashtray housing...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →