for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Rear Fog Lamp Assembly for the Defender, incorporating the direction indicator and reverse light functions within the same housing unit. Replaces a...
View full detailsCamshaft Cover for the Puma 2.4L TDCi diesel engine. This cover encloses the top of the cylinder head, housing and protecting the camshaft and valv...
View full detailsTow Bar Wiring Kit (N-Type) for the towing electrical system. This plug-and-play kit provides the 7-pin 12N 'N-type' trailer connection, feeding th...
View full detailsFloor Mat - Rear is a moulded rubber floor mat for the rear of the vehicle. It protects the rear floor, providing a hard-wearing, washable surface.
Sealing Ring for the 2.4L Duratorq TDCi diesel, sealing the thermostat into its metal housing on the engine. It forms the coolant-tight seal betwe...
View full detailsThermostat Assembly for the 2.4L Duratorq TDCi diesel, mounted in the oil cooler and filter housing. It regulates coolant flow to bring the engine...
View full detailsTiming Chain Guide - mounted within the timing cover, it guides and controls the timing chain along its run. It maintains chain alignment and work...
View full detailsHead Cylinder Gasket 3 Teeth
Head Cylinder Gasket 2 Teeth
Head Cylinder Gasket 1 Tooth
Piston Ring Set for the Td5 2.5L five-cylinder turbo diesel engine, standard size. Provides the compression and oil-control rings for one piston, ...
View full detailsCylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...
View full detailsCylinder Head Amc Early Type to 1a622423 - TD5
Bracket - Support Galvanised
Gearbox Crossmember - a chassis frame crossmember that spans the chassis rails beneath the transmission and carries the gearbox and transfer box mo...
View full detailsA/C Hose - Compressor to Condenser is the discharge line of the air conditioning refrigerant circuit, for the Td5 2.5L 5-cylinder turbo diesel. It...
View full detailsA/C Pipe - Evaporator to Compressor is the suction line of the air conditioning refrigerant circuit, for the Td5 2.5L 5-cylinder turbo diesel. It ...
View full detailsAir Conditioning Pressure Regulator Switch for the manual air conditioning refrigerant circuit. It monitors refrigerant pressure and switches the c...
View full detailsBulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...
View full detailsExtended Bump Stop - a direct replacement for the standard axle bump stop, mounting to the chassis bracket through two bolt holes. Taller than the...
View full detailsDouble DIN Fascia - a dashboard fascia panel in matt black that adapts the factory non-DIN audio aperture to accept a double-DIN aftermarket head u...
View full detailsIntercooler - the charge-air cooler in the induction system of the 300Tdi 2.5L four-cylinder turbo diesel engine. Mounted in the airflow at the fr...
View full detailsRear Flange is the rear output drive flange of the LT230 transfer box. It mounts on the transfer box rear output shaft and forms the bolted coupli...
View full detailsClutch Driven Plate is the friction disc of the Td5 clutch. Splined to the gearbox input shaft, it is clamped between the flywheel and the pressur...
View full detailsPropshaft - Rear
Rear propshaft 130"" from 2A637980
Rear Prop Shaft for the rear driveline, connecting the transfer box rear output flange to the Salisbury rear axle differential pinion. The propell...
View full detailsHalf Shaft for the rear axle drive, left-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inne...
View full detailsHalf Shaft for the rear axle drive, right-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inn...
View full detailsRear Propeller Shaft for the driveline, transmitting drive from the transfer box output to the rear axle differential. Its telescopic sliding joint...
View full detailsProp Shaft transmits drive torque from the transfer box to the rear axle differential, with a shaft length of 150.5cm. Equipped with a universal j...
View full detailsBaulk Ring (synchroniser ring) for the LT85 four-speed manual gearbox, 3.5L V8 petrol. The baulk ring forms the friction cone of the synchromesh. ...
View full detailsHub and Stud Assembly - the rear wheel hub for the Salisbury rear axle, supplied complete with wheel studs fitted. The hub carries the rear wheel ...
View full detailsFront Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...
View full detailsRear Propshaft for V8 applications, forming the link in the driveline between the transfer box and the rear axle. It transmits drive from the tran...
View full detailsIntermediate Shaft for the LT230 transfer box. The intermediate shaft carries the intermediate cluster gear that meshes between the input gear and...
View full detailsBaulk Ring (Synchroniser Ring) for the LT77 five-speed manual gearbox. Fits the mainshaft synchromesh hubs to match shaft speeds during gear engag...
View full detailsHalf Shaft for the front axle drive, left-hand side. The half shaft transmits drive from the front differential to the outer constant velocity joi...
View full detailsHalf Shaft for the front axle drive, right-hand side. The half shaft transmits drive from the front differential to the outer constant velocity jo...
View full detailsShim - 1.20 mm front axle hub shim. Fitted in the front axle hub assembly to set the correct spacing and control end-float within the half-shaft a...
View full detailsFront Brake Disc Shield - LH This pressed-steel shield mounts behind the front brake disc, between the disc and the axle swivel housing. It deflec...
View full detailsDisc brake shield RH 90/110 >KA
Shield Brake Disk
Front Propeller Shaft forms part of the driveline in 3.5L V8 petrol applications. It transmits drive from the front output of the transfer gearbox...
View full detailsHub and Stud Assembly the rear wheel hub, supplied with its wheel studs fitted. The hub mounts on the axle and carries the wheel bearings and the ...
View full detailsFront Hub and Stud Assembly for the front axle, the wheel hub complete with its fitted wheel studs. The hub carries the wheel bearings and mounts ...
View full detailsDifferential Lock Switch mounted on top of the transfer gearbox. It senses engagement of the differential lock and completes the circuit to the das...
View full detailsTop Cover Gasket for the LT85 5-speed manual gearbox. Seals the joint between the gearchange selector top cover and the gearbox casing, preventing...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →