for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...
View full detailsBolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...
View full detailsClutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...
View full detailsGearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...
View full detailsCoolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...
View full detailsExpansion Tank Cap seals the cooling system expansion (header) tank. The plastic cap closes the tank and holds the coolant circuit at its rated pr...
View full detailsDipstick Tube for the 2.25L four-cylinder petrol and diesel engines in the Series range. The tube fits into the cylinder block and guides the oil ...
View full detailsO-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...
View full detailsSwivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...
View full detailsSwivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...
View full detailsLocking plate
Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...
View full detailsSteering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...
View full detailsHex Head Bolt with a 1/4" BSF thread and a 5/8" shank length. A common application is the swivel pin housing, where it retains the swivel oil seal...
View full detailsPlain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...
View full detailsExhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...
View full detailsDrive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...
View full detailsHub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...
View full detailsCoolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...
View full detailsClutch Hose forms part of the clutch hydraulic circuit, carrying fluid between the clutch master cylinder and the slave cylinder. The flexible hos...
View full detailsThermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...
View full detailsLokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...
View full detailsLED Light Kit - 73mm
Gasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...
View full detailsBypass Hose forming part of the engine cooling circuit on the 2.5L 300TDi turbo diesel engine. It carries coolant through the bypass route at the ...
View full detailsWasher Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...
View full detailsBrake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...
View full detailsCamshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...
View full detailsLock Washer for the steering box assembly. Fitted beneath a steering box fastener to lock it against rotation, holding the joint secure under stee...
View full detailsBrake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...
View full detailsInlet Valve Stem Seal for the cylinder head valvetrain, fitted over the inlet valve stem at the top of the valve guide. The seal meters the oil pa...
View full detailsBonnet Intake Grille Set, finished in satin black with stainless steel mesh, supplied as a matched pair. The grilles fit over the bonnet air intak...
View full detailsFuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...
View full detailsRelay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...
View full detailsDoor Seal for the top of the door within the body weather-sealing system. The rubber seal fits along the upper edge of the door aperture, closing ...
View full detailsFuel Filler Hose in the fuel tank filler assembly, connecting the filler neck to the tank. It carries fuel from the filler neck into the tank duri...
View full detailsFront Mudflap Bracket for the left-hand front mudflap. The bracket mounts behind the front wheel and holds the mudflap in position, locating it to...
View full detailsClutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...
View full detailsOil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...
View full detailsDoor Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...
View full detailsHigh Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...
View full detailsO-Ring for the Td5 fuel pressure regulator. This O-ring seals the fuel pressure regulator within the Td5 fuel system, maintaining a leak-tight joi...
View full detailsBrake servo assembly for the hydraulic braking system within the Master Cylinder & Servo - Less Anti-Lock Braking System assembly group. This...
View full detailsAlternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...
View full detailsHex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...
View full detailsRear Brake Pad Set for the rear disc brakes. These friction pads locate in the rear brake calipers and clamp against the brake discs when the brake...
View full detailsscrew M5 x 12
Front Side Lamp with a clear lens and LED illumination, mounting in the front lighting position to serve as the side (parking) light. The LED draw...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →