for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...
View full detailsBleed Screw - Metric is the bleed nipple for a disc brake caliper. Threaded into the caliper body, it is opened during brake bleeding to release t...
View full detailsHeadlamp Rim is the outer trim bezel that surrounds and retains the headlamp unit in the front panel, finished in chrome. It locates over the head...
View full detailsHeater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...
View full detailsPolyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...
View full detailsIntercooler TD5 Puma
Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...
View full detailsBrake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...
View full detailsDoor Check Strap - Front - LH
Door Striker Shim is a spacer (packer) used in the side door latch and striker assembly. It fits between the body and the centre striker block, se...
View full detailsWindscreen Bracket is the left-hand mounting bracket that secures the windscreen frame to the body at its lower fixing point, for the fixed (non-fo...
View full detailsWindscreen Bracket is the right-hand mounting bracket that secures the windscreen frame to the body at its lower fixing point, for the fixed (non-f...
View full detailsWindow Regulator is the left-hand front door glass mechanism that raises and lowers the window. Part of the door internals, it mounts inside the d...
View full detailsWindow Filler Strip is a body weather-sealing trim for the side (quarter) window aperture, closing the gap between the fixed window glass and the s...
View full detailsDoor Inner Waist Seal (Front) runs along the inner waistline of the front door, sealing against the window glass. Mounted on the inboard face of t...
View full detailsHeater Blower Seal sealing the joint between the intake grille and the heater duct, for diesel applications. Fitted in the heater air intake, it cl...
View full detailsNut Plate is a captive threaded plate used in the rear end door latch assembly, providing the fixed threads onto which the tailgate latch mechanism...
View full detailsAir flow meter TD5 replacement
Rear Door Lock Seal - a gasket for the lock cover plate on the rear end door. It sits between the lock cover plate and the door skin, sealing the ...
View full detailsFuel block connector assembly (with hose) TD5
Water pump gasket Puma 2.4
Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...
View full detailsFront seat belt LH
Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...
View full detailsCamshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...
View full detailsTiming Chain for the 2.25L four-cylinder engine, part of the timing drive assembly. Drives the camshaft from the crankshaft sprocket, holding valv...
View full detailsGrab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...
View full detailsInlet Manifold Gasket End Clamp for the Rover V8 petrol engine. This metal clamp retains the inlet-manifold end seal; it is not the valley gasket o...
View full detailsCrankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...
View full detailsFlywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...
View full detailsBrake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...
View full detailsTurbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...
View full detailsRear Door Hinge Pin Kit in stainless steel - a complete repair set for the rear (side-hung) door hinges, replacing corroded or worn hinge pins toge...
View full detailsHeater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...
View full detailsDoor Check Strap limits how far the front door swings open and holds it at its detented positions. It links the door to the A-post, restraining th...
View full detailsSteering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...
View full detailsSpecial Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...
View full detailsRear Lamp Mounting Plinth for NAS-specification rear lamp installations. The plinth forms the raised mounting base that locates the rear lamp unit ...
View full detailsFront Exhaust Pipe (downpipe) for the 2.25L diesel engine, forming the first section of the exhaust system. The front pipe bolts to the exhaust ma...
View full detailsGearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...
View full detailsCore Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...
View full detailsDust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...
View full detailsBall Joint for the self-levelling suspension strut. Forms the pivoting connection at the end of the self-levelling unit, letting the strut articul...
View full detailsSuspension Spring U-Bolt for the front leaf-spring suspension, clamping the axle to the spring pack. The U-bolt wraps around the front axle tube a...
View full detailsDistributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...
View full detailsExpansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...
View full detailsGrommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...
View full detailsGasket for the carburettor-to-inlet-manifold joint in the induction system of the 2.25L 4-cylinder petrol engine. The gasket fits between the carb...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →