for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...
View full detailsLamp Guard - Round - 73mm - a protective guard that fits over a round 73 mm lamp to shield the lens. It clamps over the light unit to protect the ...
View full detailsBolt 1/4" UNF x 7/8" is a fixing bolt for the track rod and steering damper within the steering linkage. It clamps the track rod end and secures t...
View full detailsRear Fog Lamp with LED illumination, forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibili...
View full detailsStarter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...
View full detailsBrake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...
View full detailsReverse Lamp - a 95mm round LED rear reverse lamp with a clear lens, forming part of the rear lighting cluster. The lamp mounts to the round NAS-s...
View full detailsLED Light Upgrade Kit (coloured lens type) - a complete set of WIPAC 73mm LED lamps replacing the original incandescent front and rear exterior lam...
View full detailsCentre Silencer Replacement Pipe for the exhaust system, fitting in place of the intermediate (centre) silencer box. The pipe provides a straight-...
View full detailsWindscreen Seal (Roof, Inner) is the rubber weatherstrip that seals the joint between the top of the windscreen frame and the leading edge of the r...
View full detailsRear Crossmember Bolt Kit - a set of stainless steel fixings for securing the rear crossmember to the chassis. The rear crossmember is the rearmos...
View full detailsTiming Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...
View full detailsFuel tank sender and pump assembly Installed within the fuel tank, this unit forms part of the fuel tank pump and mounting assembly and integrates ...
View full detailsStud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...
View full detailsBulkhead Outrigger is a structural bracket that supports the right-hand side of the bulkhead and ties it to the chassis frame, carrying the load wh...
View full detailsFront Lamp Guards – a hinged protective guard set for the front exterior lamps. The guards mount over the front headlamps to shield the lenses fro...
View full detailsLight Guard Set - Rear Hinged rear lamp guard set that protects the rear lamp lenses from stone strike and low-speed impact during off-road use. T...
View full detailsHandbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...
View full detailsHex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...
View full detailsHex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...
View full detailsEngine Overhaul Gasket Set for the 2.5L naturally aspirated four-cylinder Land Rover diesel engine. A complete engine gasket set supplying the gas...
View full detailsOil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...
View full detailsO-Ring for the power steering hydraulic circuit, sealing a union on the 6mm power steering pipe. The O-ring seats at the connection between the po...
View full detailsRear Fog Lamp Lens is the red lens that fits to the rear fog lamp assembly. It seals over the bulb and reflector, colouring and diffusing the outp...
View full detailsLock Nut is a captive plastic fastener (commonly known as a Lokut nut) that receives a No. 10 self-tapping screw. The body pushes into a square pa...
View full detailsTailgate Cable is a retaining cable for the drop-down rear tailgate on pick-up bodies. It links the rear body panel to the tailgate and limits how...
View full detailsPower Steering Pump for the 2.5L five-cylinder turbo diesel, supplied as a complete pump assembly. Belt-driven from the engine, the pump draws flu...
View full detailsIgnition Switch - Diesel - Switch Only is the electrical switch element of the ignition system for diesel applications. It supplies the rotary swi...
View full detailsNut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...
View full detailsSelf-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...
View full detailsFuel Filler Hose in the fuel tank filler assembly, connecting the filler neck to the tank. It carries fuel from the filler neck into the tank duri...
View full detailsSteering Damper Bush is the mounting bush for the steering damper in the steering linkage. It sits at the damper mounting eye where it attaches to...
View full detailsFuel System Seal Ring
Brake Servo - Non-ABS - Valve Top Left is the vacuum brake servo in the braking system, providing pedal-assist boost. It sits between the brake pe...
View full detailsDoor Check Strap - Front - RH
Lock Barrel & Key Set - a pair of lock cylinders supplied with keys, for the vehicle's external door lock assemblies. The lock barrel is the k...
View full detailsHandbrake cover LHD
Stud Plate Retainer is part of the rear end door latch mechanism. The stud plate provides the fixed engagement point that the door latch grips to ...
View full detailsMirror Arm within the external rear-view mirror assembly. This arm mounts at the door hinge position and extends outward to position the mirror he...
View full detailsInjector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...
View full detailsOil Pump Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the oil pump to its mounting on the engine. It clamps the pump body agains...
View full detailsFront Mudflap for the right-hand front wheel arch. Mounted behind the front wheel, it deflects road spray, mud, stones and debris thrown up by the...
View full detailsTransfer Box Hi/Lo Switch is a position switch fitted to the LT230 transfer box. It belongs to the transfer box and four-wheel-drive control circui...
View full detailsDriving Member (axle drive flange) for the front and rear hub assemblies. It bolts to the outer face of the hub and engages the splined end of the ...
View full detailsDriving Member (front hub drive flange) for the front axle hub assembly. It bolts to the outer face of the hub and engages the splined end of the f...
View full detailsStub Axle Gasket for the rear axle, fitted between the stub axle flange and the end of the axle case. It seals the joint where the stub axle bolts...
View full detailsOil seal
Air intake duct hose Def 2.5DT & 200TDi air cleaner to turbocharger
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →