for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Front Radius Arm Washer for the radius arm-to-chassis mounting. It seats under the mounting bolt at the front radius arm chassis attachment. The w...
View full detailsIntercooler Hose carrying charge air from the turbocharger to the intercooler pipework, part of the charge-air (boost) circuit. It connects the tu...
View full detailsFront Wheelarch Eyebrow in gloss black plastic for the left-hand side. This trim moulding follows the upper curve of the front wheelarch, finishing...
View full detailsAccelerator Cable for the 300 Tdi 2.5L turbo diesel in left-hand-drive configuration. The cable links the accelerator pedal to the throttle lever ...
View full detailsCooling Fan for the 2.5L 300 TDi turbo diesel engine, forming part of the engine cooling assembly. The fan is driven from the front of the engine ...
View full detailsFuel Pump Rubber Mount for the fuel delivery system. This rubber mounting carries the external electric fuel pump and isolates it from the chassis,...
View full detailsBreather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...
View full detailsCarburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...
View full detailsRear Reverse Lamp - LED, Smoked - 95 mm LED reversing lamp with a smoked lens, supplied as a direct replacement for the standard rear reverse lamp....
View full detailsSingle Pipe Clip, a routing clip that retains a single pipe or line against the chassis or body. It holds fuel, evaporative-loss or brake pipework...
View full detailsSeat Belt - 3-Point Inertia Reel is a lap-and-diagonal front seat belt assembly with a self-locking inertia reel, supplied to the basic Type A spec...
View full detailsBrake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...
View full detailsCrankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...
View full detailsCoolant Hose - Pump To Thermostat is a moulded hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It connects the coolant...
View full detailsClutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...
View full detailsExhaust O-Ring Gasket for the 3.5L V8 petrol engine, sealing the joint between the exhaust manifold and the downpipe. This copper sealing ring loc...
View full detailsFront Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...
View full detailsExhaust Mount Washer
Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...
View full detailsHeated Windscreen Push Switch is the facia-mounted control switch for the heated front windscreen circuit. Pressing the switch energises the heati...
View full detailsHorn - High Note
Reverse Lamp is part of the rear lighting assembly, mounted at the rear of the vehicle. The lamp illuminates the ground behind the vehicle when re...
View full detailsExhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...
View full detailsSpring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...
View full detailsFuel Pipe from the Td5 2.5L 5-cylinder turbo diesel fuel system, running on the low-pressure side between the inline fuel filter and the pump. It ...
View full detailsLock Washer fitted under a nut or bolt head to resist loosening from vibration. An M10 shakeproof (external-serrated) washer. The serrated teeth b...
View full detailsWasher from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...
View full detailsDrive Flange operates within the rear differential and final drive assembly, providing the bolted coupling that transmits drive torque between the ...
View full detailsRear Shock Absorber provides damping control on the rear axle for suspension set up with approximately 50 mm of additional travel. Twin-tube const...
View full detailsOutrigger is a tubular structural member that bolts to the rear of the chassis to support the body and rear cross-member, transferring load into th...
View full detailsEngine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...
View full detailsFront brake caliper piston repair kit used within the front brake disc and caliper assembly. The components install inside the hydraulic caliper ...
View full detailsFront Indicator Lens for the front direction indicator (turn signal) lamp. Supplied as the lens only; it does not include the lamp holder. The len...
View full detailsABS Wheel Speed Sensor - Front for the 4-wheel ABS braking system. Mounted at the front axle, the sensor reads a toothed reluctor ring and generat...
View full detailsBrake Pad Set for the rear disc brakes, supplied as an axle set together with a fitting kit. The brake pads are the friction elements that the cal...
View full detailsSpring nut
Starter Motor for the engine starting system - a 12V high-torque gear-reduction unit for petrol applications. The starter mounts to the bellhousin...
View full detailsAir Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...
View full detailsReverse Lamp Lens is the clear lens that fits to the rear reverse (reversing) lamp assembly. It seals over the bulb and reflector and diffuses the...
View full detailsAlternator Brush Set replaces the carbon brushes in an ACR-type alternator, within the charging system. The brushes bear on the rotor slip rings a...
View full detailsWash/Wipe Switch is the steering-column stalk switch that controls the windscreen wiper and washer functions. Mounted on the steering-column switc...
View full detailsWiper Arm - windscreen wiper arm, left-hand. The 7mm is the wide width of the arm, which sets the wiper-blade fitting - it is not a spindle size. ...
View full detailsCooling Fan Assembly drives airflow through the radiator within the engine cooling system, supplied complete with the fan drive. The integrated vi...
View full detailsRadiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...
View full detailsExhaust Pipe Clamp
Fuel Feed Pipe for the diesel fuel supply system, routing fuel from the tank toward the engine. It forms the feed leg of the fuel delivery circuit...
View full detailsFuel Tank Assembly is the main fuel storage vessel of the fuel system. It holds the fuel supply and feeds it to the fuel pump and delivery lines, ...
View full detailsBrake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →