for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Upper Rear Door Hinge, aluminium, for the rear end (tailgate) door, part of the body and door assembly. It is the upper of the two hinges that car...
View full detailsTailgate Buffer - rubber buffer for the rear tailgate (tailboard). This rubber buffer cushions the tailgate where it meets the body, absorbing the...
View full detailsCable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...
View full detailsExhaust Manifold Stud for the 3.5L V8 petrol engine, securing the exhaust manifold to the cylinder head. The stud screws into the head and carries...
View full detailsLock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...
View full detailsCylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...
View full detailsCylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...
View full detailsSealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...
View full detailsDrain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...
View full detailsDouble-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...
View full detailsGlow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...
View full detailsHex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...
View full detailsDifferential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...
View full detailsRadius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...
View full detailsOil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...
View full detailsDecal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...
View full detailsSeal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...
View full detailsSteering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...
View full detailsInlet & Exhaust Manifold Gasket - 300TDi
Window Channel
Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38
Radius Arm Bush - Front for the front suspension radius arm assembly. This rubber bush is pressed into the forward end of the front radius arm and...
View full detailsMaster Lighting Switch mounted on the steering column, providing the primary control for the side lights and headlamps. It forms part of the steer...
View full detailsRear Shock Absorber - hydraulic telescopic damper for the rear suspension. Mounted between the rear axle and the chassis, it damps the oscillation...
View full detailsLucas Reverse Light Switch for the specified R380 manual-gearbox applications using the AMR3918 switch reference. It completes the reverse lamp cir...
View full detailsFront Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...
View full detailsGasket kit 300tdi lower block set no rear crankshaft seal
Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...
View full detailsRear shock absorber
Brake caliper 110/130 LH rear
Brake Caliper - Rear - RH
Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...
View full detailsRivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...
View full detailsTow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...
View full detailsIgnition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...
View full detailsShock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...
View full detailsConnecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...
View full detailsMain Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...
View full detailsCoolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...
View full detailsIdler Tensioner Pulley for the auxiliary (serpentine) drive belt system. Mounted on the automatic belt tensioner arm, the pulley bears against the ...
View full detailsCoolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...
View full detailsCoolant Hose - Radiator Upper is the upper hose in the engine cooling circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries hot coolant from...
View full detailsEngine mounting
Radiator Rubber Mount for the engine cooling system. This rubber mounting locates the radiator in its support panel and cushions it against engine ...
View full detailsSnap sac
Hinge Packer Shim for the door hinge assembly. Fitted between the hinge and its mounting face to set door alignment. Adding or removing shims adju...
View full detailsSteering Damper Assembly for the front axle steering linkage. The hydraulic damper mounts across the steering linkage, where it controls lateral o...
View full detailsBlanking Plug Grommet for the dash assembly. This rubber plug fills an unused aperture in the dash panel - such as the opening for the hand throttl...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →