for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Oil Pump Shaft & Gear for the 3.5L V8 petrol engine, part of the lubrication system. The shaft and its drive gear transmit rotation from the ca...
View full detailsWindscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...
View full detailsDouble Cardan Front Propshaft Kit - a heavy-duty front propshaft for the LT230 transfer box, using a double cardan (constant-velocity) joint at the...
View full detailsService Filter Kit gathers the filters required for a routine engine service on the 2.5-litre diesel, in both naturally aspirated and turbo diesel ...
View full detailsSteering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...
View full detailsRear Wing Protector - protective panel fitted over the top edge of the rear wing to shield the paintwork and panel surface from scuffs, scratches a...
View full detailsAcoustic Mat System - a moulded cabin sound-insulation set that lines the transmission tunnel and adjacent floor area to reduce noise transmission ...
View full detailsUpgrade your Land Rover Defender (1987-2006, 2007-2016) or Series 3 with the WIPAC LED 73mm smoked lamp kit. Smoked LED style light for a sleek...
View full detailsBall Joint Service Tool for the steering drop-arm ball joint. The tool presses the drop-arm ball joint (part RBG000010) into and out of the drop a...
View full detailsExterior Door Handle for the front right-hand door, right-hand drive configuration. Mounted on the outer door skin, the handle forms part of the e...
View full detailsHexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...
View full detailsWindow Regulator Escutcheon - trim finisher that locates over the manual window winder spindle on the inner door, concealing the regulator aperture...
View full detailsRadius Arm Bolt with a 5/8" UNF (Unified National Fine) imperial thread and a 3-1/2" shank length. Secures the front radius arm to its axle or cha...
View full detailsBolt 1/4" UNF x 2-1/2"
Clutch gasket
Steering Column Switch - Wash/Wipe - the column-mounted stalk switch that operates the windscreen wiper and washer functions. Mounted on the steer...
View full detailsAlternator assembly within the engine charging system, installed on the front-end accessory drive and driven by the auxiliary belt to convert mecha...
View full detailsRear wiper motor
Bonnet Alarm Switch
Caged Nut - a captive plastic nut that receives a self-tapping or trim screw. It clips into a panel aperture to provide a fixed threaded seat, use...
View full detailsPDWA Switch (Pressure Differential Warning Actuator) is part of the brake hydraulic circuit, bridging the two independent front and rear pressure l...
View full detailsPinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...
View full detailsOil Strainer Gasket for the Rover V8 petrol engine, sealing the flanged joint of the oil pick-up strainer inside the sump. Renew it whenever the p...
View full detailsOil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...
View full detailsInput shaft oil seal
Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...
View full detailsSpire Nut is a spring-steel push-on fastener used to retain body panels and trim. The clip slides over a panel edge or hole and self-threads onto ...
View full detailsOil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...
View full detailsCarburettor Grommet for the twin Stromberg carburettor installation on the V8 petrol engine. It sits in the air cleaner and carburettor air intake ...
View full detailsU-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...
View full detailsHalf Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...
View full detailsIgnition Switch - Petrol - Steering Column is the electrical ignition and starter switch mounted in the steering column, forming part of the igniti...
View full detailsOil Filler Cap Assembly for the rocker (valve) cover of the 2.25L 4-cylinder petrol engine. The cap seals the oil filler neck and incorporates an i...
View full detailsClutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...
View full detailsInlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...
View full detailsValve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...
View full detailsInjector Pipe No.3, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...
View full detailsInjector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...
View full detailsHot Plug - 2.0L & 2.25L Diesel
Core Plug seals a casting aperture in the cylinder block or head of the 2.25L and 2.5L four-cylinder petrol engines. Also known as an expansion or...
View full detailsDifferential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...
View full detailsDifferential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...
View full detailsBrake Pipe for the front braking hydraulic circuit. This is the flexible pipe that feeds the front wheel cylinders. It connects the chassis-mounte...
View full detailsExhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...
View full detailsHeater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...
View full detailsRubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...
View full detailsRear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...
View full detailsHoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →