Land Rover Discovery 1 Parts

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Upper Turret Mounting Bracket, galvanised, forming part of the front coil spring and damper turret mounting on the chassis. The bracket provides t...

Trim Clip is a panel-retaining fastener used to secure interior door casing and exterior bodyside and drip-rail trim to the body. Part of the body...

Water reservoir grommet rubber seal

Interior Door Handle for the left-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the latc...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Brake servo assembly for the hydraulic braking system within the Master Cylinder & Servo - Less Anti-Lock Braking System assembly group. This...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Bypass Hose forming part of the engine cooling circuit on the 2.5L 300TDi turbo diesel engine. It carries coolant through the bypass route at the ...

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Grommet

Rubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Brake Caliper Carrier Bolt secures the brake caliper carrier (mounting bracket) to the axle, providing the clamping force that holds the caliper as...

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Track spacer oil seal

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Drain plug LT77 R380

Clutch Kit is a matched three-piece clutch assembly for the 2.5L 200TDi and 300TDi turbo diesel engines with manual transmission. The kit renews t...

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Rear Shock Absorber, standard-travel, for the rear axle suspension. The damper controls vertical movement of the rear axle and damps spring oscill...

Output Shaft Seal for the extension housing of the ZF 4-speed automatic gearbox. The seal fits at the rear of the gearbox, where the output shaft ...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Washer 20mm

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Reservoir assy

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Oil Separator Drain Hose for the 300 Tdi 2.5L 4-cylinder turbo diesel engine, part of the crankcase ventilation system. It returns the oil collect...

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...