Land Rover Discovery 1 Parts

Inlet Valve for the cylinder head valvetrain of the 200TDi 2.5L 4-cylinder turbo diesel engine. The valve seals against its seat in the cylinder h...

Viscous unit

Layshaft Nut for the R380 five-speed manual gearbox. It secures the layshaft gear cluster on its shaft, torqued to specification and then staked in...

Rear Screen Wiper Motor with Mounting Bracket for the rear wash/wipe system. The motor drives the rear wiper arm across the tailgate glass. Suppli...

Front Steel Winch Bumper with a black protective finish, replacing the standard front bumper to add front-end protection and an integral winch moun...

Heater Blower Resistor for the air conditioning climate control system. It regulates the speed of the blower motor, controlling the force of the ai...

Battery Tray is the offside (right-hand) carrier tray that supports and locates the battery in the engine bay. It forms the mounting platform on w...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Towing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...

Adjustable Panhard Rod - lateral axle location link, supplied with polyurethane bushes. The panhard rod locates the axle laterally relative to the...

Mirror - Manual is a manually-adjusted exterior door mirror. It mounts to the door and is adjusted by hand, without electric operation.

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Filter Kit 3.9 EFI

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Central exhaust pipe Discovery 300TDI Stainless Steel

Rear Bumper End Cap - LH is the left-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where i...

Rear Bumper End Cap - RH is the right-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where ...

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Oxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...

Rear Door Wiper Arm for the tailgate wiper system. Mounts to the rear wiper spindle on the tailgate and carries the wiper blade across the rear wi...

Door Lock Actuator Electric actuator in the central door locking system. Mounted within the door, it drives the latch to the locked and unlocked p...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Distributor Drive Gear - V8

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Reservoir bracket

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Clutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...

Camshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Body Mount - To Chassis Frame is a rubber isolation mount positioned at one of the body-to-chassis attachment points. The mount cushions the body ...

Flanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...

Drive Flange Nut - Front secures the front drive flange (driving member) to the wheel hub, as part of the front hub assembly. It retains the drivi...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Head Gasket - Metal for the 3.9L V8 EFI engine, sealing the cylinder head to the engine block in the top-end assembly. This multi-layer steel head...

Piston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Rear Wiper Blade - the wiper blade for the rear screen wash/wipe system. It clips onto the rear wiper arm and draws its rubber wiping element acro...

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Handbrake Expander Assembly for the drum-type transmission (parking) brake mounted at the rear output of the transfer box. The expander sits betwe...