Land Rover Discovery 1 Parts

Sensor oxygen INTERMOTOR

Differential Bearing Shim - 0.063in

Seat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...

Exhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Headlamp Assembly - Front, Left Hand for left-hand-drive applications, part of the front exterior lighting circuit. The unit combines the reflecto...

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Steering Shaft - the intermediate shaft in the steering column assembly. It links the steering column to the steering box input, transmitting rotat...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Oil Filter Housing Adaptor - part of the oil filter and oil cooler assembly. It mounts on the oil filter housing and provides the connection betwee...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Exhaust Manifold Heat Shield mounts over the exhaust manifold to protect surrounding components from radiant heat. It deflects heat away from adja...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Door Glass Channel the glass run channel within the door assembly. The channel guides the door glass as it is raised and lowered by the window reg...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Bulb & Holder - Green, an illumination bulb supplied in its colour-coded green holder for the dashboard and switch panel lighting circuits. Th...

O-Ring seals the joint between the sump and the ladder-frame assembly on the 2.5L 200TDi diesel engine.

Throttle Spring - the return spring in the throttle linkage. Acting on the throttle body spindle, it closes the throttle butterfly and returns the ...

Screw is a fixing used in the front bumper assembly, securing bumper components to their mounting points.

Accelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...

Front Bumper for the Discovery 1, fitting the pre-facelift body specification across petrol and diesel engine variants. This steel bumper mounts t...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine (reconditioned). The injector atomises high-pressure diesel delivere...

Rear Door Assembly - the rear side door for the passenger compartment, forming part of the vehicle's body and closures group. The door hangs from ...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...

Exhaust Valve seats in the cylinder head of the 3.5L V8 petrol engine. It controls the exhaust gas leaving the combustion chamber. Head diameter 3...

Intake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...

Hose Clip clamps a hose onto its spigot or fitting, maintaining a sealed joint under pressure.

Cross Rod End

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Front Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On

Roof Rack - a full-length roof rack in heat-treated aluminium extrusion, giving a low-profile, low-noise platform. A groove (slot) system runs alo...

Number Plate Mounting Plinth for use with a front winch bumper. Winch bumpers often have no dedicated number plate location, as the fairlead and w...

Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...

Nyloc Locknut - M6 - M6 hex nyloc (nylon insert) locknut. The nylon insert grips the bolt thread to resist loosening under vibration without requi...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...