Land Rover Discovery 1 Parts

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Breather O-Ring for the 2.5L diesel engine (NA Diesel, 200 TDi and 300 TDi), used in the crankcase ventilation system. It seals the cyclone breath...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Front driveline propellor shaft connecting the transfer box output to the front axle differential within the drive mechanism. (60cm in 65cm) Trans...

Clutch Release Bearing Staple is the spring retention clip that secures the clutch release bearing onto the release fork. It holds the bearing in p...

Speedometer Drive Gear for the LT230 transfer box, located on the rear output and driving the speedometer take-off. This is the 20-tooth gear, ide...

Automatic Drive Belt Tensioner for the front-end accessory drive system, maintaining correct tension across the auxiliary belt that drives the alte...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Panhard Rod Bushes are the mounting bushes at the ends of the front panhard rod in the coil-sprung front suspension. The panhard rod locates the fr...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Copper Washer - copper sealing washer used at threaded and banjo unions in the engine oil circuit. Forms a soft metal-to-metal seal that crushes t...

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Coolant Bypass Hose for the engine cooling system of the 200 TDi diesel engine. It carries coolant along the bypass path so that flow continues to...

Locking plate

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Upper Turret Mounting Bracket, galvanised, forming part of the front coil spring and damper turret mounting on the chassis. The bracket provides t...

Trim Clip is a panel-retaining fastener used to secure interior door casing and exterior bodyside and drip-rail trim to the body. Part of the body...

Water reservoir grommet rubber seal

Interior Door Handle for the left-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the latc...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Brake servo assembly for the hydraulic braking system within the Master Cylinder & Servo - Less Anti-Lock Braking System assembly group. This...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Bypass Hose forming part of the engine cooling circuit on the 2.5L 300TDi turbo diesel engine. It carries coolant through the bypass route at the ...

Brake Pad Spring Kit retains the front brake pads within the caliper, holding them against rattle and locating them on the pad retaining pins. For...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Grommet

Timing Belt Kit - 200TDi is a timing system service kit for the 200Tdi 2.5L turbo-diesel engine. The kit renews the components that maintain camsh...

Rubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Brake Caliper Carrier Bolt secures the brake caliper carrier (mounting bracket) to the axle, providing the clamping force that holds the caliper as...

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Track spacer oil seal

Top Coolant Hose for the V8 petrol engine, part of the engine cooling circuit. The upper radiator hose carries heated coolant from the engine outl...

Drive Belt (V-belt) for the engine accessory drive system, transferring rotation from the crankshaft pulley to a driven accessory. This is a 13 mm...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Drain plug LT77 R380

Stop Light Switch mounts at the brake pedal and switches the rear brake (stop) lamps on when the pedal is depressed, operating within the brake-lig...

Clutch Kit is a matched three-piece clutch assembly for the 2.5L 200TDi and 300TDi turbo diesel engines with manual transmission. The kit renews t...

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...