Land Rover Discovery 1 Parts

Piston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Heated Rear Window Switch mounts in the instrument binnacle and controls the heated rear window (backlight) demist circuit. The push-operated swit...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Sensor oxygen INTERMOTOR

Differential Bearing Shim - 0.063in

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Exhaust Manifold Heat Shield mounts over the exhaust manifold to protect surrounding components from radiant heat. It deflects heat away from adja...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Front Bumper for the Discovery 1, fitting the pre-facelift body specification across petrol and diesel engine variants. This steel bumper mounts t...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine (reconditioned). The injector atomises high-pressure diesel delivere...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...

Hose Clip clamps a hose onto its spigot or fitting, maintaining a sealed joint under pressure.

Cross Rod End

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Front Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On

Roof Rack - a full-length roof rack in heat-treated aluminium extrusion, giving a low-profile, low-noise platform. A groove (slot) system runs alo...

Number Plate Mounting Plinth for use with a front winch bumper. Winch bumpers often have no dedicated number plate location, as the fairlead and w...

Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...

Nyloc Locknut - M6 - M6 hex nyloc (nylon insert) locknut. The nylon insert grips the bolt thread to resist loosening under vibration without requi...

Track Rod Washer from the steering linkage. It seats at the track rod fixing, spreading clamp load beneath the retaining nut to secure the joint.

Shock Absorber Boots are protective covers that fit over the shock absorber body to shield the shaft and seal from mud, grit and debris. Supplied ...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in silver, ET00 offset. The pressed-steel construction withstands o...

Locking Wheel Nut Set secures the road wheels to the hub with a keyed nut pattern that cannot be removed with a standard socket, deterring wheel th...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the modular pattern, finished in white, ET08 offset. The pressed-steel construction withstands of...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in white, ET00 offset. The pressed-steel construction withstands of...

Steel Road Wheel - 7 x 16 pressed-steel wheel in the 8-spoke pattern, finished in black, ET00 offset. The pressed-steel construction withstands of...

The Winrace T multi-spoke alloy wheel is engineered for extreme off-road conditions, making it a top choice for Baja, Dakar, and cross-country raci...

The Winrace T multi-spoke alloy wheel is engineered for extreme off-road conditions, making it a top choice for Baja, Dakar, and cross-country raci...

Mainshaft Gear for the LT230 transfer gearbox, carrying 26 teeth. The gear is mounted on the transfer box mainshaft and forms part of the gear tra...

Alloy Wheel from the Maxtrac Blindo range, finished in anthracite. Specifications: Size: 16 x 7 inches Bolt pattern (PCD): 5 x 165 Offset (E...

Connecting Rod Assembly for the 300TDi 2.5L turbo diesel engine. The connecting rod links a piston to the crankshaft, transmitting the force of co...

Pinion Shaft is the mainshaft of the LT77 five-speed manual gearbox, running through the gear cluster to carry the driven gears and transmit drive ...

The Jackall 48" Large Base Jack is the ultimate heavy-duty lifting solution for a variety of applications. With a massive 8,000lbs capacity, this j...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Raised Air Intake (Snorkel) - relocates the engine air intake from the inner wing up to roof height, drawing induction air from above the bonnet li...

Adjustable Tow Hitch STC8060AB BA186