Land Rover Discovery 1 Parts

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Decoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. It cradles the anti-roll bar at its ...

Bottom hose

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Hose Clip for radiator hose connections on 4-cylinder TDi diesel engines. This screw-type hose clip secures the upper and lower radiator hoses at ...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Shock Absorber Washer - Rear - a retaining washer used at the rear suspension shock absorber mounting. It seats against the lower shock absorber b...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Bottom Hose is the lower radiator hose in the engine cooling circuit. It carries coolant from the base of the radiator back to the water pump inle...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

Locknut is a self-locking M10 nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibration, m...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Brake Pipe Clip - a triple retaining clip for the brake hydraulic pipework. It holds three brake pipes together along the chassis run, maintaining...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...