Land Rover Discovery 2 Parts

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Caged Captive Nut - an M8 nut held in a spring-steel cage that clips into a panel or bracket to provide a captive threaded fixing. It anchors the ...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Exhaust Manifold for the Td5 2.5L five-cylinder turbo diesel engine. The cast manifold bolts to the exhaust ports on the cylinder head and collect...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Clutch Kit renews the friction components of the Td5 driveline clutch and is supplied without the release bearing. The kit comprises the clutch co...

Self-Tapping Screw - a No. 8 x 1/2" self-tapping screw used as a body-trim fixing. It secures body trim panel brackets, headlamp finisher panels a...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Ball Steel Bearing

Wiper Arm Pivot Nut Secures the wiper arm to the splined pivot spindle of the windscreen wiper mechanism. It threads onto the spindle where it emer...

Stud

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Flywheel Assembly for the 2.5L Td5 five-cylinder turbo diesel engine, mounted between the engine and the manual gearbox. Bolted to the rear of the...

Tow Ball – 50 mm a black-finished towing ball for flange-type towing brackets. The ball bolts to the face of the towing bracket on the standard tw...

Steel hex full nut, M8 x 1.25 thread, catalogued for the clutch and dual-mass flywheel assembly on the Td5 2.5L 5-cylinder turbo diesel engine. Th...

Cam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Relay (yellow) fitted in the under-bonnet fuse and relay box of the vehicle's electrical system. The relay uses a low-current control signal to sw...

Selector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Cylinder Head Gasket Set for the Td5 2.5L 5-cylinder turbo diesel, supplying the ancillary seals and gaskets used around the cylinder head when it ...

Drive Meter Speedo Gear Yellow 22 Teeth

Temp Sensor

Bearing transfer box OEM TIMKEN

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Screw is a threaded fastener used to secure components during assembly.

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Screw for securing the engine wiring harness in Rover V8 petrol engine installations. Fastens harness clips and mounting brackets to the engine bl...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Snorkel Head is the 3" ram-air intake head that fits to the top of a raised air intake tube, forming the forward-facing scoop that feeds cool, clea...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...