Land Rover Discovery 2 Parts

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Connecting Rod Bolt for the Rover V8 EFI petrol engine, part of the connecting rod assembly in the engine bottom end. The bolt clamps the connecti...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Yoke Transmission

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Clevis pin

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Self-Tapping Screw - a No. 8 x 1/2" self-tapping screw used as a body-trim fixing. It secures body trim panel brackets, headlamp finisher panels a...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Valve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Needle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Seat Belt Stowage Clip from the rear seat belt assembly. It retains the seat belt webbing in a stowed position when the belt is not in use, holdin...

Relay (yellow) fitted in the under-bonnet fuse and relay box of the vehicle's electrical system. The relay uses a low-current control signal to sw...

Selector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Banjo bolt

Oil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...

Distributor Gear

Drive Meter Speedo Gear Yellow 22 Teeth

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Engine Dowel, a precision locating dowel that sets the relative position of mating engine components during assembly. The dowel fixes the exact al...

Hex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...