Land Rover Discovery 2 Parts

Dzus Fastener is a quarter-turn quick-release stud used to secure the radiator cowl and cooling fan shroud within the engine cooling assembly. The...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Inlet Manifold Gasket for the Rover V8 petrol engine, sealing the inlet manifold where it seats in the valley between the two cylinder banks. This...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Handbrake Adjuster Repair Kit for the cable-operated transmission drum handbrake. The kit renews the adjuster mechanism of the drum brake mounted ...

Level plug R380

Cylinder Head Bolt (Long) for the V8 petrol engine, securing the cylinder head to the engine block. This is the longer of the two head bolt length...

Cylinder Head Bolt (Short) for the V8 petrol engine, securing the cylinder head to the engine block. This is the shorter of the two head bolt leng...

Washer Reservoir Cap

Fan Bearing supports the engine cooling fan on the Td5 front cover. Mounted to the timing cover, the bearing carries the viscous cooling fan and i...

Transfer Box Hi/Lo Switch is a position switch fitted to the LT230 transfer box. It belongs to the transfer box and four-wheel-drive control circui...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Cylinder Head Installation Kit for the Td5 2.5 five-cylinder turbo diesel. It supplies the fitting components used when installing the cylinder he...

Crankshaft Thrust Washer for the 2.5L Td5 five-cylinder diesel engine, supplied in the standard thickness. Fitted at the thrust main bearing, the ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Spring Washer - M10 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to...

Drain/fill plug magnetic axle

Rear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Differential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...

Stud is an M10 threaded stud, 35 mm long, used as a mounting fastener at several engine locations - the cylinder head, manifold, power steering pum...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Oil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...

Bleed Screw for the coolant bleed point on Td5 engines. The screw seats in the bleed port on the top coolant hose and is opened to release trapped...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Exhaust Valve for the Rover V8 EFI petrol engine, fitted in the cylinder head valvetrain. The valve seals the exhaust port during the combustion c...

Oil Pump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the oil pump to its mounting face on the engine. It forms the oil-tight j...

Fuel Pressure Regulator mounts on the fuel rail of the multiport electronic fuel injection (EFI) system. It holds a constant pressure difference b...

Cooling Fan Assembly drives airflow through the radiator within the engine cooling system, supplied complete with the fan drive. The integrated vi...

Fuel Block Connector for the Td5 2.5L 5-cylinder turbo diesel engine, incorporating the fuel pressure regulator at the fuel block. It forms the ju...

TD5 oil cooler adaptor gasket

Cylinder Head Gasket for the Rover V8 petrol engine, sealing the joint between one cylinder head and the engine block. It seals the combustion cha...

Fan Bearing supports the engine cooling fan on the Td5 front cover. Mounted to the timing cover, the bearing carries the viscous cooling fan and i...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Coolant Elbow forms part of the coolant outlet on the Td5 2.5L 5-cylinder turbo diesel engine. It directs coolant leaving the cylinder head water ...

Collapsible spacer transfer box

Plain Nut - an M10 threaded fastener used at engine and chassis fixing points. Applications include retaining the shock absorber mountings to the ...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Fuel Filter & Sedimentor Assembly - Td5

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...