Land Rover Discovery 2 Parts

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Front door window regulator assembly for left-hand front door applications within the door glass operating mechanism. This component forms part o...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Bumper Lamp rear left-hand assembly, part of the rear bumper lighting cluster. The unit combines the reverse lamp and rear fog lamp in a single ho...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Bumper Lamp rear right-hand assembly, part of the rear bumper lighting cluster. The unit combines the rear fog lamp and direction indicator in a s...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Windscreen Washer Jet A heated twin-nozzle washer jet that directs washer fluid onto the windscreen. It seats into the scuttle or bonnet panel and ...

Window Regulator Motor - RH is the electric drive motor for the right-hand window regulator assembly. It mounts directly to the window regulator m...

Bumper Lamp Assembly, left-hand side, part of the rear bumper lighting cluster. A combined lamp unit with a red lens section serving the stop and ...

Rear Bumper Lamp from the rear lighting assembly - the right-hand (RH) unit mounted in the rear bumper. The combined lamp carries the reversing li...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Foam Pad - Air Intake Deflector seals the air intake deflector in the scuttle area, where fresh air is drawn into the heating and ventilation syste...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Windshield wiper arm D2 LHD

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Oil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Front door window regulator forming part of the door glass operating assembly, responsible for controlled raising and lowering of the electric wind...

Bonnet Release Cable for the bonnet-release mechanism. It links the interior release lever to the bonnet latch: pulling the cabin lever draws the ...

Skeleton Front Shock Absorber Turrets are the upper mounting towers for the front shock absorbers, bolting to the front chassis rails. The open tu...

Upgrade your Land Rover Discovery 2 with this heavy-duty front winch bumper, designed for strength, durability, and off-road capability. Constructe...

Window Regulator Motor - LH is the electric drive motor for the left-hand window regulator assembly. Mounted directly to the regulator mechanism, ...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Trim Rivet, an 8 x 20mm plastic drive (pin-type) rivet used to secure trim panels and mouldings to the body, typically wheel arch trims, bumpers an...

Intermediate shaft lock nut LT230

Rear End Door Hinge - Upper for the rear end door (tailgate) assembly on Land Rover Discovery 1 and Discovery 2. This upper hinge mounts at the to...

Spare Wheel Carrier is the mounting bracket assembly that carries the spare wheel on the rear door. It bolts to the rear door and provides the stu...

Water Rail O-Ring for the 4.0L and 4.6L V8 petrol engine, sealing a connection on the coolant water rail. The water rail distributes coolant acros...

Battery Clamp Turnbuckle is the threaded hold-down fitting that secures the battery within the battery tray. The turnbuckle engages the battery cl...

Rear Wiper Arm - wiper arm for the rear windscreen, part of the rear wash/wipe system. Fits onto the rear wiper motor spindle and carries the wipe...

Upgrade the rear protection of your Discovery 2 with this Rear Heavy Duty Bumper, made from 4mm steel and finished in a sleek black powder coat. Th...

Mirror Glass for the left-hand exterior door mirror, convex profile. Part of the exterior mirror assembly. The convex curvature widens the rearwar...

Rear End Door Hinge - Lower for the rear end door (tailgate) assembly on Land Rover Discovery 1 and Discovery 2. This lower hinge mounts at the ba...

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...