Land Rover Discovery 2 Parts

Fir Tree Fastener in light grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancilla...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Pedal Rubber Pad for the foot pedal. The moulded rubber pad slips over the pedal arm to provide a durable, non-slip foot surface. Fitted to manual...

Trim Retention Clip for securing door casing and bodyside trim panels. This push-fit clip engages a panel stud on the door inner frame or body str...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

High/Low Lever Gaiter - the flexible boot that seals the transfer box high/low range selector lever where it passes through the centre console. Fi...

Window switch

Handbrake Lever Gaiter - the boot that seals the parking brake lever where it passes through the centre console. It covers the handbrake lever piv...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Heater Control Bulb illuminates the heater and ventilation control panel. Fitted into the front HVAC control assembly, it backlights the heater co...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Sunvisor Retainer - the clip that holds the sunvisor in its stowed position against the headlining. The retainer fixes to the headlining and recei...

Gaiter Retrim Kit - a three-piece set of replacement lever gaiters for the centre console. The kit re-covers the three transmission-tunnel levers ...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Gear Lever Gaiter - black gaiter supplied with its housing, fitting over the main gear lever where it passes through the centre console. It seals ...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Heated Seat Element Assembly for the front seat squab (the backrest), part of the seat heating circuit. The heating pad sits behind the squab trim...

Fastener used to secure interior door casing panels and body side trim. Retains door casing and rear body panel trim on applicable vehicles.

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Front Seat Armrest Finisher, the decorative trim panel forming the visible outer surface of the front seat armrest on the Discovery 2. Applies to ...

Floor Mat Set — moulded rubber floor mats for the front footwells, protecting the cabin floor and carpet. The tailored rubber mats sit in the driv...

Pan Head Bolt, M8 x 40mm. Metric pan head bolt for use across Land Rover body, chassis, and interior assemblies.

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Holder - Cup

Holder - Cup

Dash Repair Kit in grey - a set of pre-formed overlay panels that fit over the existing upper dashboard moulding. The panels cover the areas of th...

Door Casing Stud - plastic push-fit stud used to secure interior trim panels to the door frame and body structure. The stud passes through the tri...

Cup Holder for the vehicle interior.

Load Space Rubber Mat - Half Length - moulded rubber protective mat for the rear load area. The mat lies directly on the load floor and covers the...

Windscreen Wash/Wipe Switch - steering column stalk switch controlling the front wiper and washer circuits. The switch mounts to the column switch...

Load Space Rubber Mat - Full Length - moulded rubber protective mat covering the full length of the rear load area. The mat lies directly on the l...