Land Rover Discovery 2 Parts

Rear Step Shock Absorber for the retractable rear step assembly. Gas-charged strut that damps and controls the step's movement as it deploys and r...

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

Rear Differential Assembly - the complete crown wheel and pinion assembly in its carrier, bolting into the rear axle casing. The unit takes drive ...

Rear Flange is the rear output drive flange of the LT230 transfer box. It mounts on the transfer box rear output shaft and forms the bolted coupli...

Clutch Driven Plate is the friction disc of the Td5 clutch. Splined to the gearbox input shaft, it is clamped between the flywheel and the pressur...

Cup Holder for the facia console, a pull-out tray-type holder mounted in the dashboard. The holder slides out from the facia to support beverage c...

Turbo Hose for the Td5 2.5L 5-cylinder turbo diesel induction system. Forms part of the air cleaner assembly, ducting filtered intake air from the...

Finger Follower transfers camshaft lift to the valve in the Td5 2.5L 5-cylinder turbo diesel valvetrain. It sits between the camshaft lobe and the...

Grommet is a sealing grommet fitted to the engine oil sump on V8 petrol engines. It seals the point where a tube or fitting passes through the sum...

Piston Assembly is a complete engine piston for the Td5 2.5L 5-cylinder turbo diesel. It runs in the cylinder bore and transmits combustion pressu...

Idle Speed Control Actuator for the V8 EFI petrol engine. It fits to the throttle body and meters air past the closed throttle plate, allowing the ...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...

Wheel Centre Cap for steel road wheels, finished in black. Fits over the wheel centre and covers the wheel nuts. Supplied individually; four are r...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Rear Tonneau Finisher - the textured-black rear quarter moulding that trims the rear body panel on the left-hand side. This exterior finisher fits...

Rear Chassis Leg - a 600 mm repair section for the offside (right-hand) rear chassis rail. Replaces the corroded rear end of the chassis rail, cut...

Wheel Adaptor Kit, supplied as a set of four. The adaptors mount to the existing hubs and re-centre the wheel, allowing alloy wheels of the same st...

Air-to-Coil Conversion Fitting Kit - the mounting hardware needed when converting the rear air suspension to coil springs, supplied without the spr...

Air-to-Coil Conversion Kit - Heavy Duty - a complete kit that replaces the rear self-levelling air suspension with a conventional coil-spring syste...

Roof Rack Floor Section - a marine plywood load platform for a roof rack. It fits into the companion DA4732 roof rack frame to provide a solid, we...

Waterproof Seat Cover Set for the front seats, supplied as a pair. Tailored to fit over the standard front seats and protect the original upholste...

Rear Spring Mount Bracket - the chassis-mounted bracket that forms the seat for a rear coil spring. It locates the top of the spring against the c...

Steering & Sump Guard - underbody skid plate. This guard fits beneath the front of the vehicle to shield the steering linkage and the engine s...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Protect your Land Rover Discovery 2 with these heavy-duty Rock & Tree Sliders, designed to shield your sills and lower body panels from off-roa...

Window Regulator Rear - Discovery 2 - LH

Door Seal - Rear End Door is the weatherstrip seal for the rear end door. It seals the rear end door aperture against water and draught ingress.

Rear Side Door Seal the primary door aperture seal for the left-hand rear side door, mounted on the body around the door opening. This moulded rub...

Rear Side Door Seal the primary door aperture seal for the right-hand rear side door, mounted on the body around the door opening. This moulded ru...

Front Door Seal the primary door aperture seal for the left-hand front door, mounted on the body around the door opening. This moulded rubber weat...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.

Interior Mirror & 2 - Discovery 1

Glass Channel - window glass guide channel for the rear side door. Guides and locates the door glass as it is raised and lowered, supporting smoot...

Active Cornering Enhancement (ACE) Pump for the Discovery 2. This hydraulic pump is the primary pressure source within the ACE system, which activ...

Wheel Nut Cover Removal Tool for Land Rover alloy wheel locking nut covers. This dedicated tool is designed to grip and extract the protective pla...

UJ Fitting Kit

Blanking Plug Fills the headlamp washer jet aperture in the front bumper on vehicles not fitted with headlamp washers. It presses into the moulded ...

Rear Chassis Leg - a 600 mm repair section for the nearside (left-hand) rear chassis rail. Replaces the corroded rear end of the chassis rail, cut...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Snorkel - a raised air intake that relocates the engine's air inlet from the standard wing position up to roof height, drawing air from a higher, c...

Front Door Lock Assembly for the front door latching system, fitted to the right-hand front door on left-hand-drive vehicles. The assembly houses ...