Land Rover Discovery 2 Parts

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Flange Bolt, M12 - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing area an...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Bolt for the brake caliper carrier. Secures the caliper carrier bracket to the hub on disc-brake assemblies, retaining the carrier against braking ...

Oil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...

Locking Nut - an M12 self-locking nut used to secure suspension linkage fasteners. The locking feature resists loosening under the vibration and c...

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Master Lighting & Indicator Switch, a column-mounted stalk within the steering column switch assembly. It controls indicator operation and head...

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Thermostat housing replacement

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Oil Pressure Switch - tapered thread, engine lubrication circuit. Screws into the oil gallery - at the pump, the filter housing or the oil cooler ...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Bolt Threaded fastener used within the exhaust system assembly.

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Side Indicator is a wing-mounted side repeater lamp in the vehicle's direction-indicator circuit, supplied as a pair. Each unit uses LED elements ...

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...