Land Rover Discovery 2 Parts

Spring Seat is the lower seat for the rear coil spring, forming the located surface that the base of the spring sits on. It positions and retains ...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Skeleton Front Shock Absorber Turrets are the upper mounting towers for the front shock absorbers, bolting to the front chassis rails. The open tu...

Wheel Nut - retaining nut for the rear door-mounted spare wheel. This nut secures the spare wheel to its carrier on the rear door. Its seat is pro...

Steering Box Assembly - LHD is the power-assisted recirculating-ball steering box, in the left-hand-drive configuration. It is the central unit of...

Thermostat housing replacement

Fuel Connector Block for the Td5 2.5L 5-cylinder turbo diesel engine (Euro III, later specification). The block is the central junction of the fuel...

Timing Chain Guide for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The guide runs al...

CLUTCH KIT - COVER + PLATE + BEARING - TD5 - D2/DEF 83-06

External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...

Airflow sensor 4L V-8 engines

Cylinder Head Bolt (Long) for the V8 petrol engine, securing the cylinder head to the engine block. This is the longer of the two head bolt length...

Cylinder Head Bolt (Short) for the V8 petrol engine, securing the cylinder head to the engine block. This is the shorter of the two head bolt leng...

Upgrade your Land Rover Discovery 2 with this heavy-duty front winch bumper, designed for strength, durability, and off-road capability. Constructe...

Gaiter Retrim Kit - a three-piece set of replacement lever gaiters for the centre console. The kit re-covers the three transmission-tunnel levers ...

Rear Air Spring Conversion Kit replaces the rear air suspension with conventional coil springs. It removes the self-levelling air springs from the...

Window Regulator Motor - LH is the electric drive motor for the left-hand window regulator assembly. Mounted directly to the regulator mechanism, ...

Mud Flap for the left-hand side, covering both the front and rear wheel positions. Part of the exterior body protection. Fitted behind the wheel a...

Main Switch - heavy-duty main electrical switch rated at 1000A. Switches the primary high-current circuit, suited to continuous heavy-duty loads.

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Seat yoke

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Silicone Intercooler Hose Kit - a set of silicone charge-air hoses for the TD5 turbo and intercooler circuit, replacing the standard rubber hoses t...

Dial Illumination Bulb for the climate control panel, providing backlighting for the heating and ventilation controls. It seats behind the switch ...

Trim Rivet, an 8 x 20mm plastic drive (pin-type) rivet used to secure trim panels and mouldings to the body, typically wheel arch trims, bumpers an...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Radio Remote Control Receiver - 433MHz unit for the Discovery 2 central locking and alarm system. Fitted in the roof headlining, this receiver pic...

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...

Front Left-Hand Indicator Lamp Assembly for the pre-facelift Discovery 2 (1999-2002). This amber turn signal lamp unit is mounted at the front lef...

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Intermediate shaft lock nut LT230

Oil Cooler Hose Pipe - RH, Transmission in the automatic transmission oil cooling circuit. This is the right-hand pipe that carries automatic tran...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Washer Dowty sealing washer for the Active Cornering Enhancement (ACE) hydraulic anti-roll system. It seals the pipe-to-actuator union, fitting at...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the green, thin-sectio...

Fuel Cooler for the diesel fuel return circuit. Mounted in the return line between the fuel injection system and the tank, it dissipates heat pick...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Head Gasket - TD5 - 1-Hole seals the joint between the cylinder head and cylinder block on the Td5 2.5L 5-cylinder turbo diesel engine. The 1-hole...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Panhard Rod Bolt - M16 × 70mm flanged hexagonal head. This bolt secures the panhard rod at its mounting bracket, retaining the rod that locates th...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...