Land Rover Discovery 3 Parts

Flanged Nut, M8. The integral flange spreads clamp load across the joint face and removes the need for a separate washer. Used in the exhaust syst...

Brake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly. The carrier bolts to the rear hub carrier and holds t...

Brake Caliper Carrier - Rear - the fixed bracket of the rear sliding-caliper brake assembly, dimensioned for the rear disc size used with the 18-in...

Adjusting Nut is an M17 flanged nut used in the rear suspension toe link assembly. It locks the toe link adjuster at its connection to the rear kn...

Brake Pedal Pad for automatic transmission applications - the moulded rubber cover that fits over the brake pedal lever in the pedal box assembly. ...

Handbrake Shoe Fitting Kit

Inlet Manifold Seal for the 4.4L AJ V8 petrol engine, sealing the lower inlet manifold to the cylinder head within the air induction system. It cl...

Front Brake Caliper Carrier - machined adaptor that mounts the front brake caliper to the hub carrier. The carrier bolts to the suspension upright...

Front Brake Pad Fitting Kit - pad guide pin and boot set for the front brake caliper. The guide pins pass through the caliper and locate the brake...

Drive Belt Tensioner maintains correct tension on the auxiliary drive belt within the front-end accessory drive. The spring-loaded arm and integra...

Front wheel arch moulding cap - right-hand side, exterior body trim. The cap closes off the front wheelarch moulding where it meets the bumper, co...

Air Suspension Compressor Cover - Upper is the upper half of the protective housing that encloses the air suspension compressor. It shields the co...

Coolant hose connecting the radiator to the coolant expansion tank. Carries displaced coolant and air from the radiator into the expansion tank as...

O-Ring, 11mm - a sealing ring used in the power steering hydraulic circuit, at the union joints of the pressure supply and return hoses. It seats ...

Gear Selector Lever - lever that clamps to the manual selector shaft on the six-speed ZF automatic transmission, forming the gearbox end of the flo...

Fuel Injector Seal - Lower is the lower sealing ring fitted to the fuel injector, within the fuel injector and pipe assembly of the 4.4L V8 (AJ) pe...

Upper radiator hose connecting the radiator to the thermostat housing. Carries hot coolant from the thermostat housing into the radiator top conne...

Rear wheel arch moulding cap - right-hand side, exterior body trim. The cap closes off the rear end of the rear wheelarch moulding where it meets ...

Sensor - Crankshaft Position - CPS

Air Bleed Valve is fitted to the engine cooling system to release air trapped in the coolant circuit. Opened during filling and bleeding, the valv...

Shock Absorber Boot - Rear

Ignition Wire Assembly for the ignition system of the 4.0L V6 petrol engine (Cologne V6 SOHC). The high-tension leads carry the spark voltage from...

Ride Height Sensor for the air suspension system, front right-hand corner. The sensor measures the position of the suspension arm relative to the ...

Air Suspension Compressor Cover - Lower is the lower half of the protective housing that encloses the air suspension compressor. It shields the co...

Auxiliary Drive Belt - polyvee belt for the accessory drive on the 4.0L Cologne V6 SOHC EFI petrol engine. Driven from the crankshaft pulley, the ...

Suspension Arm Bush is the rear hydraulically damped bush (hydrabush) pressed into the front lower suspension arm. The fluid-filled hydrabush isol...

Water Outlet Connection - the coolant outlet housing on the 2.7L V6 diesel engine, incorporating the thermostat that controls coolant flow to the r...

Air Suspension Strut Boot Kit - front, part of the front suspension strut and spring assembly. The boot fits over the front air suspension strut a...

Rear moulding cap - exterior body trim. The cap closes off the moulding at the junction between the rear bumper and the rear wheelarch moulding, c...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Coolant Hose connecting the water outlet to the cylinder head within the engine cooling system. Part of the heater circuit, this hose routes coola...

Power Steering Rack Pipes - the pair of rigid transfer pipes that run across the steering rack body and carry hydraulic fluid from one end of the r...

Door Switch Assembly - driver's door switch pack for the front door trim casing, combining the electric window lift rockers with the exterior mirro...

Inlet Manifold Gasket for the 4.4L AJ-V8 petrol engine, sealing the joint between the inlet manifold and the cylinder head port face. The gasket m...

Connecting Rod Bolt for the connecting rod assembly of the TDV6 / TDV8 turbo diesel V-engine. The bolt clamps the big-end cap to the connecting ro...

Air Suspension Pipe Kit - installation pipework for an AMK-type air suspension compressor. The kit supplies the air lines that connect the compres...

Steering Column Rotary Coupler - the rotary coupling, or clock spring, mounted on the upper steering column behind the steering wheel as part of th...

Number Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It sits in the rear number plate surround an...

Crankshaft Trigger Wheel provides the timing reference for the crankshaft position sensor. Mounted at the flywheel, the toothed reluctor wheel rot...

Suspension Arm Fitting Kit - the mounting hardware for a front upper suspension arm (wishbone) on the front independent suspension. The kit contai...

Suspension Arm Fitting Kit - the replacement fasteners used when a rear lower suspension arm is renewed. The arm's pivot bolts pass through the re...

Air Suspension Kit supplying the compressor for the Electronic Air Suspension (EAS) system. The compressor generates the pressurised air that infl...

Circlip for the manual transmission gearbox, used in the gear-selector detent mechanism. It retains the detent spring and plunger that hold the se...

Outer Door Handle is the exterior handle for the side doors and fits both front and rear positions. This version is for vehicles equipped with the...

Brake Tube for the rear hydraulic braking circuit, forming the right-hand rear pipe run to the caliper. The rigid tube carries pressurised brake f...

Brake Tube for the rear hydraulic braking circuit, forming the left-hand rear pipe run to the caliper. The rigid tube carries pressurised brake fl...