Land Rover Discovery 3 Parts

24v dsl long belt

Heated Windscreen Push Switch is the facia-mounted control switch for the heated front windscreen circuit. Pressing the switch energises the heati...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Tube - Water Outlet

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Wiper Switch Assembly

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Tow Hook Protective Cap is a cover for the towing eye aperture in the bumper. It closes off the tow hook mounting point when not in use, keeping o...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Rear Window Heated Switch

Rear Mudflap Kit mounts at the rear of the vehicle to reduce road spray and protect the lower bodywork and rear window from mud and debris. Intend...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Cigar Lighter Ring - Illuminated

Switch

Height Sensor Jumper Lead for the electronic air suspension system. This connecting lead links a ride-height sensor to the chassis wiring harness,...

Roof Rack Fitting Kit - the mounting hardware that secures a roof rack system to the vehicle's longitudinal roof rails. It supplies the fixing par...

Gear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...

Rear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...

Spring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...