Land Rover Discovery 3 Parts

Lower Inlet Manifold Gasket sealing the lower section of the inlet manifold assembly on the AJV8 petrol engines. It forms the joint between the lo...

Water Pump Gasket

Primary Timing Chain Guide (Lower) for the AJV8 petrol engine, located in the lower timing gear. It guides the primary timing chain, maintaining c...

Fuel Injector for the 4.4L AJV8 petrol engine, forming part of the electronic sequential fuel injection system. The injector meters and atomises p...

Chain Timing

Timing Chain Tensioner maintains correct tension on the timing chain of the 4.4 AJV8 petrol engine, taking up slack as the chain wears to hold accu...

Camshaft Position Sensor reports camshaft position on the AJV8 petrol engine to the engine management system, providing the timing reference for ig...

Camshaft Sensor monitors camshaft position on the AJV8 petrol engine, providing the reference signal the engine management system uses to control i...

Oil Cooler Assembly in the engine oil cooling circuit of the AJ-V8 4.4L petrol engine. It dissipates heat from the circulating engine oil, holding...

Front Crankshaft Oil Seal for the AJV8 4.4L petrol engine, sealing the front of the crankshaft where it passes through the timing gear cover. It r...

Connecting Rod Bearing – Yellow is a big-end bearing shell for the connecting rod of the 4.4 V8 AJ petrol engine, carrying the rod on the crankshaf...

Connecting Rod Bearing – Green is a big-end bearing shell for the connecting rod of the 4.4 V8 AJ petrol engine, carrying the rod on the crankshaft...

Bearing - Crankshaft Main

Connecting Rod Bearing – Blue is a big-end bearing shell for the connecting rod of the 4.4 V8 AJ petrol engine, carrying the rod on the crankshaft ...

Upper Inlet Manifold Gasket sealing the upper section of the inlet manifold assembly on the 4.4L V8 EFI petrol engine. It forms the joint between ...

Timing Cover Seal for the AJV8 petrol engine - a rubber seal fitted to the timing gear cover. It seals the timing gear cover against the cylinder ...

Bearing - Crankshaft Main

Main Bearing Blue Upper

Timing Chain Tensioner - Lower in the timing chain drive of the AJ-V8 petrol engine (4.4L and 4.2L supercharged). It maintains correct tension on ...

Injector Retaining Bolt - M6 x 35 mm clamp bolt in the fuel injection system of the V6 and V8 diesel engines. The bolt secures the injector hold-d...

PTFE Split Seal - a split polytetrafluoroethylene sealing ring used in the variable cam timing (VCT) gear of the AJ-series V8 petrol engine. The s...

Crankshaft Thrust Washer locates within the crankshaft main bearing assembly, seating at the thrust main bearing journal. It controls crankshaft e...

Cylinder Head Bolt - M10 x 175mm bolt clamping the cylinder head to the block on the AJ-series V8 petrol engine. A torque-to-yield fastener; twent...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Thermostat for the 4.4L AJ V8 and 4.2L Supercharged V8 petrol engines, fitted within the engine cooling circuit. The thermostat regulates coolant ...

Brake Shoe Set - Axle Set

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Head Gasket - V8 - RH seals the right-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between...

Automatic Transmission Fluid for ZF 6HP Series Transmissions, supplied in a 1-litre bottle. This fluid is formulated from a blend of hydrocracked ...

Hex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Land Rover Oval Name Badge - Plastic - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground, moulded in ...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Head Gasket - V8 - LH seals the left-hand cylinder head to the engine block on the 4.4L AJ-V8 petrol engine. It forms the gas-tight joint between ...

Valve Stem Seal for the cylinder head valvetrain on TDV6 and TDV8 diesel engines. Fitted to both inlet and exhaust valves, the seal presses onto th...

Oil Filter for the engine lubrication system of the 4.4L V8 petrol (EFI) and 4.2L V8 supercharged petrol engines. The filter removes wear particle...

Oil Filter for the engine lubrication system of the 4.4L V8 petrol (EFI) and 4.2L V8 supercharged petrol engines. The filter removes wear particle...

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Brake Shoe Set - No Fittings - Axle Set

Alternator Assembly

Brake Shoe Set

Coolant Level Warning Sensor for the engine cooling system. This sensor is fitted to the coolant expansion tank and monitors coolant level via an ...