Land Rover Discovery Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This is the pl...

Joint washer exhaust TD5

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Fuel Injector Harness for the Td5 fuel injection system, carrying the electrical connection between the engine wiring loom and the electronic unit ...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Steering drop arm lever for left-hand drive steering box applications. This component connects the steering box output shaft to the steering linka...

Front cover oil seal

Major Service Kit for the 2.5L Td5 engine, containing the filtration and service consumables for a full scheduled service. Kit contents: 1 x oil f...

Nyloc Nut with a 1/2" UNF thread, used to retain suspension and steering ball-joint fixings. A nylon insert set into the crown of the nut deforms ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Radius Arm Bump Stop - Rear for the rear suspension radius arm assembly. This bump stop limits upward suspension travel at the rear axle, providin...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Diesel Fuel Filter - Cartridge is the replaceable filter element that seats in the fuel filter housing, upstream of the fuel injection pump in the ...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Front Camshaft Oil Seal for the Td5 2.5L 5-Cylinder Turbo Diesel engine, fitted at the timing end of the camshaft within the cylinder head. Seated...

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Cam Cover Gasket for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This gasket seals the camshaft cover to the top of the cylinder head, preventing...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Exhaust Manifold to Turbo Gasket seals the joint between the exhaust manifold outlet and the turbocharger inlet within the exhaust manifold and tur...

Rear Reflector mounts in the rear lamp area as part of the rear lighting and signalling assembly. A passive retroreflector that returns incident l...