for Discounts / VAT
for Discounts & Correct VAT
OEM, genuine, and aftermarket parts for the Land Rover Discovery Sport (L550), produced from 2014 to present. Covers pre-facelift D8-platform and post-facelift PTA-platform variants, including Ingenium diesel and petrol, Haldex AWD, and P300e PHEV builds. Over 100 parts in stock in the Netherlands with EU-wide delivery. For parts across all Discovery generations, see the Land Rover Discovery parts collection.
Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...
View full detailsoil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...
View full detailsBolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...
View full detailsoil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...
View full detailsOil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...
View full detailsCrankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...
View full detailsOil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...
View full detailsOil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...
View full detailsFlange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsOil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...
View full detailsExhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...
View full detailsEGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...
View full detailsFlange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsEGR Valve Gasket
Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...
View full detailsBlanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...
View full detailsMagnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...
View full detailsGasket polygon shape type. cover
Fuel Injector - high-pressure common-rail injector for the 2.0L AJ21D4 Ingenium diesel, mid power output. The injector is clamped into the cylinde...
View full detailsRear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...
View full detailsPiston Ring Set in standard size for the Ingenium AJ200D / 204DTD 2.0L 4-cylinder diesel engine. The rings seal the combustion chamber against the...
View full detailsCoolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...
View full detailsExhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...
View full detailsValve Tappet, 2.2L DW12 Diesel (Td4)
Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...
View full detailsCoolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...
View full detailsSump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...
View full detailsTiming Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...
View full detailsFuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...
View full detailsCrankshaft Locking Tool - 2.0 Diesel AJ200D
Front Crankshaft Oil Seal Fitting Tool - 2.0 Diesel AJ200
Diesel Particulate Filter - AJ20D4 Diesel - EU6D
Diesel Particulate Filter - AJ20D4 Diesel - EU6D
Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...
View full detailsEGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...
View full detailsExhaust Gas Pressure Sensor for the low-pressure EGR circuit on the 2.0-litre four-cylinder diesel engine. It measures exhaust gas pressure and sig...
View full detailsExhaust Gas Pressure Sensor for the diesel particulate filter (DPF) circuit on the 2.0L I4 AJ200D diesel engine. The sensor measures exhaust gas p...
View full detailsKnock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...
View full detailsOil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...
View full detailsGasket for the Variable Valve Lift Unit, sealing the variable valve lift unit to the cylinder head on the 2.0L AJ200/AJ20P4 four-cylinder petrol en...
View full detailsCylinder Head Bolt securing the cylinder head to the cylinder block on the 2.0L 16V Ti-VCT turbocharged petrol engine. The bolt clamps the head, h...
View full detailsInjector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...
View full detailsExhaust Gas Pressure Sensor mounted in the front pipe / catalyst section of the exhaust system. The sensor measures exhaust gas pressure and repor...
View full detailsInjector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...
View full detailsAccessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...
View full detailsThermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...
View full detailsEmission Gasket for the crankcase cover, part of the crankcase ventilation and emission-control system on the 2.0L AJ200/AJ20D4 four-cylinder diese...
View full detailsTiming Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...
View full detailsParts for the compact Land Rover Discovery Sport (L550), built from 2014 to present. JLR D8 pre-facelift and PTA post-facelift phases covered, Ingenium and Ford-era engines, Haldex and Active Driveline AWD, P300e PHEV. Same-day EU dispatch from the Netherlands.
The Discovery Sport (L550) is the compact crossover in the Land Rover range. It launched in late 2014 as the replacement for the Freelander 2 (L359) and is engineered as a five-door unibody crossover, not a body-on-frame SUV. Its closest mechanical relative is the Range Rover Evoque, with which it shares platforms across both production phases. The Discovery Sport is a separate vehicle from the full-size Discovery 5 (L462): different platform, different engine layout, different drivetrain, no parts interchangeability.
All Discovery Sport variants use transversely-mounted engines and lack a low-range transfer case. Most variants carry either Haldex Generation 5 on-demand AWD or the GKN Active Driveline system, with selected diesel variants in some markets fitted as front-wheel drive only. The 9-speed ZF 9HP automatic was standard on pre-facelift cars (a 6-speed Getrag manual was available on some lower diesels), and an 8-speed Aisin automatic is fitted to the P300e plug-in hybrid.
Built on the JLR D8 platform, also referenced in JLR documentation as LR-MS, shared with the first-generation Range Rover Evoque (L538). The 2015 model year launched with Ford-sourced engines: the 2.0-litre EcoBoost petrol and the 2.2-litre Duratorq diesel. From the 2016 model year onward these were replaced by the JLR Ingenium AJ200 family in 2.0-litre four-cylinder petrol and diesel forms.
Moved to the Premium Transverse Architecture (PTA) platform shared with the Jaguar E-Pace and the second-generation Range Rover Evoque (L551). PTA brought 48-volt mild-hybrid hardware to the Ingenium diesel and petrol engines, enabled the P300e plug-in hybrid (1.5-litre three-cylinder petrol plus an 80 kW motor and an 8-speed Aisin transmission), and updated the exterior styling, lighting, track width, and infotainment.
Across the 2019 boundary, body trim and many fasteners carry over. Engine, drivetrain, and emissions hardware do not. Each product listing names the applicable year range or variant where fitment is restricted.
Use the engine variant, year, and category filters above the product grid to narrow this collection to parts that match your specific Discovery Sport.
The Discovery Sport carries four practical fitment-relevant divisions: pre-facelift versus post-facelift (2019 boundary), engine family (Ford-sourced 2015 only, Ingenium thereafter, plus the P300e three-cylinder PHEV from 2020), drivetrain configuration (FWD eD4 in some markets, Haldex AWD as standard, GKN Active Driveline as option, PHEV AWD on the P300e), and transmission (9-speed ZF, 6-speed Getrag manual on some diesels, 8-speed Aisin on the P300e). All of these need to be confirmed before ordering drivetrain or powertrain parts.
The 17-digit VIN on the windscreen base plate or driver-side door jamb is the most reliable starting point. The 10th character identifies model year. The 2015 model year (10th character F) is a critical boundary because that vehicle alone uses Ford engines rather than Ingenium. Drivetrain configuration is not encoded in any single VIN character but can be confirmed from the V5C or the original build sheet, and visually from under-vehicle inspection of the rear differential and propshaft fitment.
Land Rover publishes official Discovery Sport specifications and model year guidance at landrover.com/discovery/discovery-sport. For engine code identification and the Ford-to-Ingenium transition detail, the Land Rover Discovery Sport Workshop Manual lists the applicable component codes by model year.
Discovery Sport stock covers conventional suspension and steering (no air suspension is fitted to this model), braking, engine and ancillaries for the Ingenium and Ford-era engines, cooling for both engine families, Haldex and Active Driveline driveline service parts, electrical and sensor service items, and routine service kits. Click any category to filter results to L550 fitment.
Coil springs, dampers, control arms, bushings, and steering parts for the L550. No air suspension is fitted to this model.
Suspension and steering partsDiscs, pads, calipers, and hydraulic parts for the Discovery Sport across both production phases.
Brake system partsService parts for the Ingenium 2.0-litre diesel and petrol, the Ford EcoBoost and Duratorq engines on 2015 model year vehicles, and the 1.5-litre three-cylinder petrol on the P300e.
Engine partsThermostats, water pumps, radiators, expansion tanks, and coolant hoses for transversely-mounted Ingenium and Ford-era engines.
Cooling and heating partsRear propshaft, Haldex Generation 5 service parts, GKN Active Driveline components, CV joints, and driveshaft items.
Drive mechanism partsSensors, switches, lighting, and electrical service parts for the L550 across pre and post-facelift specifications.
Electrical partsOil, fuel, air, and pollen filter combinations matched to engine and model year for scheduled servicing.
Service kitsThe Discovery Sport sits across two engine families and two platforms within a single nameplate, so the tier decision matters most on engine and drivetrain parts where pre-facelift Ford-era and Ingenium components are not interchangeable.
Genuine is the appropriate tier for the Haldex coupling internals, the Active Driveline rear drive module, the 9HP transmission rebuild components, the P300e plug-in hybrid battery and motor service parts, and emissions hardware on the Ingenium diesel. These are systems where calibration history and JLR part numbers matter for warning code suppression and warranty integrity.
OEM is the practical default for most service work. ZF supplies the 9HP transmission and fluid (specifically the ZF Lifeguard 9). Bosch supplies most ignition, sensor, and diesel injection hardware on the Ingenium. GKN supplies the Active Driveline rear drive components. Magna BorgWarner supplies the Haldex couplings. Brembo and TRW supply braking. The OEM tier matches Genuine specification at lower cost.
Aftermarket covers wear-driven and consumable parts: brake friction surfaces, filters, bushings, bulbs, fasteners, and body trim clips. Listings name the supplier where the OEM identity is confirmed, so the source is explicit before purchase.
EU Stock and DispatchL550 parts ship from the Netherlands warehouse. Working-day orders placed before 15:00 CET are dispatched the same day. Intra-EU shipments are duty-free with no import VAT at the border, with typical transit of 1 to 2 working days to Benelux, Germany, and France, and 2 to 4 days to the Nordics, Iberia, Italy, and central Europe. UK customers are served under standard post-Brexit customs procedures. Regular workshop customers can request invoiced trade terms.
Technical GuidesThe guides below cover the diagnostic and service questions that come up most often on the L550.
A direct cost-of-ownership comparison between the body-on-frame Discovery 4 (L319) and the compact Discovery Sport (L550) for European owners. Covers maintenance spend, common fault patterns, and the practical differences that matter when choosing or running either model.
Discovery 4 vs Discovery Sport guideA diagnostic procedure for the 2.0-litre Ingenium diesel as fitted to the Discovery Sport. Covers the failure modes upstream of thermostat or water pump replacement so the correct component gets ordered first time.
Overheating diagnosis guideA fuel system diagnostic guide for Ingenium diesel-equipped vehicles including the Discovery Sport. Covers the most likely causes of a crank-no-start condition and identifies which fuel system components to inspect before ordering.
Crank no start diagnosis guideNo, and this is the most common point of confusion when ordering parts. The Discovery Sport (L550) is a compact crossover SUV built on a transverse-engine platform (JLR D8 from launch, PTA from the 2019 facelift), shared most closely with the Range Rover Evoque. It has no low-range transfer case and uses either Haldex or GKN Active Driveline AWD. The Discovery 5 (L462) is a full-size, longitudinal-engine SUV on the JLR D7u aluminium platform, sharing structure with the Range Rover L405 and Range Rover Sport L494. It has permanent four-wheel drive with a two-speed transfer case and low range. The two vehicles share neither platform nor major mechanical components, and parts are not interchangeable. Make sure you are on the correct collection page before ordering.
Close. The Discovery Sport shares its platform with the Range Rover Evoque across both production phases. Pre-facelift Discovery Sport (2014 to 2019) is on the JLR D8 platform shared with the first-generation Evoque (L538, 2011 to 2018). Post-facelift Discovery Sport (2019 onward) moved to the Premium Transverse Architecture shared with the second-generation Evoque (L551, 2018 onward) and the Jaguar E-Pace. This means many platform-level components, suspension geometry, drivetrain hardware, and engine mounts are common between Discovery Sport and Evoque of the corresponding generation. Body panels, interior trim, and exterior styling are model-specific.
The Discovery Sport launched in late 2014 (2015 model year) using engines carried over from the Freelander 2 era: the 2.0-litre EcoBoost petrol and the 2.2-litre Duratorq turbodiesel, both sourced from Ford. The JLR Ingenium engine family entered Discovery Sport production from the 2016 model year onward, replacing the Ford units with the 2.0-litre AJ200 four-cylinder diesel and petrol engines. The 2015 model year is therefore the only Discovery Sport that runs Ford engines, and its engine, fuel system, and emissions parts are completely separate from all later model years. Confirm the engine code via VIN before ordering anything in those categories.
The Discovery Sport uses transverse-engine on-demand AWD, either the Haldex Generation 5 coupling (standard) or the GKN Active Driveline system (optional). Both systems engage the rear axle electronically when needed, neither includes a low-range transfer case, and neither has a centre differential in the conventional sense. Some pre-facelift diesel variants were sold as front-wheel-drive only (the eD4) in selected markets. By contrast, the Discovery 5 uses permanent four-wheel drive with a longitudinal layout, a Torsen centre differential, and a two-speed transfer case with low range. Drivetrain parts between the two models are completely separate.
Yes. The P300e variant is supported across service categories: the 1.5-litre Ingenium three-cylinder petrol engine, the 8-speed Aisin automatic transmission, the high-voltage cooling system, and the standard service items shared with the rest of the L550 range. High-voltage battery service parts and electric motor components are stocked at Genuine and OEM tiers where available. Working on a PHEV requires high-voltage qualification, and a qualified workshop should always isolate the system before any high-voltage work. Standard chassis, brake, and body service parts on the P300e are the same as the mild-hybrid Discovery Sport of the same year.
For in-stock items, the typical timeline is same-day dispatch on orders confirmed before 15:00 CET, with delivery in 1 to 2 working days to Benelux, Germany, and northern France, and 2 to 4 days to the wider EU. Carrier tracking is issued at dispatch. For workshops handling regular L550 volume, the trade account route gives invoiced terms, faster checkout, and a single point of contact for backorder queries.