Genuine Land Rover Parts

Cylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...

double washer, restrictor

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Thermostat regulates coolant flow within the engine cooling system, with an opening temperature of 82°C. It remains closed while the engine is col...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Windscreen Bracket Spacer is a packing piece used in the windscreen mounting assembly, seating between a fixed windscreen bracket and its body moun...

Front Mudflap for the right-hand front wheel arch. Mounted behind the front wheel, it deflects road spray, mud, stones and debris thrown up by the...

Timing Chain Tensioner for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The tensioner...

O-ring

Engine Lifting Bracket bolts to the cylinder head and provides a rated attachment point for hoisting the engine. Fitted to the four-cylinder petro...

Front Door Glass Guide channels the window glass as it travels within the front door. This run guide locates the edge of the door glass and keeps ...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Military fuel cap

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Oil Filler Pipe Gasket seals the joint between the oil filler pipe and the engine front (timing) cover. Fitted at the filler pipe mounting flange,...

Clevis Pin for the front door hinge and check strap assembly. This pin secures the door check strap (travel limiter) at its pivot, retaining the s...

Fan Cowl shrouds the engine cooling fan at the rear of the radiator. It channels the airflow drawn by the fan through the radiator core, improving...

Aerial – Front Wing is the wing-top radio antenna for the vehicle audio system. The all-metal telescopic mast mounts to the top of the front wing ...

Rear Fog Lamp Switch is the dashboard-mounted control for the rear fog lamp circuit. This switch allows the driver to activate the rear fog lamp f...

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Driveshaft Spacer - a 15.5mm spacer used within the front and rear axle drive shaft and hub assembly. The spacer sits between the drive shaft and ...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Rear Mudflap for the left-hand side, part of the exterior underbody protection assembly. Fitted behind the rear wheel, it shields the lower rear b...

Front Mudflap for the left-hand front wheel arch. Mounted behind the front wheel, it deflects road spray, mud, stones and debris thrown up by the ...

Mudflap – Rear – RH is the right-hand rear mudflap, fitted behind the rear wheel to reduce road spray and protect the bodywork from mud and stone t...

Radiator Grille - the front grille panel that fits in the front body aperture ahead of the radiator. It admits cooling airflow to the radiator whi...

Timing Chain Guide for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The guide runs al...

Escutcheon

Door Latch Link Clip secures the operating link rod within the door latch and locking assembly. It retains the connecting linkage that transfers m...

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

Breather Filter is the crankcase ventilation filter mounted at the rocker cover on the V8 EFI petrol engine. It filters oil vapour and mist from t...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Spring Ring

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...