Genuine Land Rover Parts

24v dsl long belt

Heated Windscreen Push Switch is the facia-mounted control switch for the heated front windscreen circuit. Pressing the switch energises the heati...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Wiper Switch Assembly

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Tube - Water Outlet

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Rear Window Heated Switch

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Hub to Knuckle Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle within the front suspension and hub assembly.

Oil Separator is part of the crankcase ventilation system on the 2.7L V6 Lion diesel engine. It separates oil mist from the crankcase blow-by gase...

Exhaust Gas Temperature Sensor measures exhaust gas temperature at the front of the diesel particulate filter, in the upstream section of the after...

Dual Note Horn - the audible warning horn assembly, part of the electrical system, supplied as a matched pair on a common mounting bracket. The se...

Headlamp Bulb Cover is the rear sealing cap that fits over the bulb aperture at the back of the headlamp housing. It seals the housing against dus...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Asy Lamp

Exhaust Gas Temperature Sensor for the diesel exhaust aftertreatment system, fitted to vehicles equipped with a diesel particulate filter (DPF). T...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Washer - Sealing

Disc - Brake

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...