Genuine Land Rover Parts

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Bush

Hook

Grommet - Blanking Plug, Gearbox Tunnel for Land Rover Series II and III. This small rubber blanking plug fits into an aperture in the top of the ...

Oil Tube Gasket seals the turbocharger oil drain (return) pipe where it joins the engine, within the turbocharger lubrication circuit. After lubri...

Front Seat Belt Assembly - the left-hand front inertia-reel belt, part of the front seat belt restraint system for soft-top configurations. It is ...

Cylinder Head Installation Kit - No Bolts

Differential Pinion Shim - 0.062" selective shim used to set the pinion position within the differential (final drive) assembly. Fitted at the pin...

Tailgate Rubbing Strip Fixing Plate from the tailgate assembly. The plate provides the fixing point for the tailgate rubbing strip, backing the st...

Body Finisher - Rear Capping - LH is a pressed steel exterior trim panel that caps the top of the rear body side on the Defender 110 two-door hardt...

Body Finisher - Rear Capping - RH for the rear body on the Defender 110 two-door hard top and soft top. This right-hand rear body capping finisher...

Flywheel Bolt for the Td5 2.5L 5-cylinder turbo diesel with automatic transmission. It secures the drive plate to the rear flange of the crankshaft...

Oil Pump Screw secures the oil pump assembly within the lubrication system of the 2.25L 4-cylinder petrol engine.

Oil Cooler Pipe Seal for the transmission oil cooler circuit. The seal fits at the oil cooler pipe union, sealing the connection against fluid lea...

Cigar Lighter Knob - the removable knob and heating element of the cigar lighter, part of the body electrical ancillaries. The knob pushes into th...

Differential Shim for the crownwheel and pinion assembly. Fitted during differential assembly to set bearing preload and gear alignment. Shim thic...

Pad R380

Front Seat Cushion Repair Kit - the seat base cushion for the front seat frame, supplied in half-leather / half-cloth trim. The cushion is the low...

Pipe - Fuel

Coolant Hose for the engine cooling circuit, connecting the thermostat housing to the coolant pump pipe. Fitted to the 2.4L Td4 four-cylinder turb...

Alloy Wheel - a 7J x 16" five-spoke cast alloy road wheel with a dual (two-tone) finish. The spoke face carries embossed lettering as a styling de...

Tailgate Assembly is the complete side-hinged lower tailgate (tailboard) for the rear of the vehicle, carrying the externally mounted spare wheel. ...

Oil Filter for the 2.2L Puma turbo diesel engine. The filter removes metal particles, carbon and other contaminants from the circulating engine oi...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Differential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...

Mainshaft Spacer for the LT77 five-speed manual gearbox fitted to V8 models. Locates on the gearbox mainshaft to set the correct axial spacing and...

Gearbox Mainshaft Shim for the manual transmission gearbox. Used during gearbox assembly or overhaul to set correct mainshaft end-float. Selecting...

Throttle Spring - the return spring in the throttle linkage. Acting on the throttle body spindle, it closes the throttle butterfly and returns the ...

Accelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...

Centre Floor Heelboard Carpet - left-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the ...

Centre Floor Heelboard Carpet - right-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the...

Intake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...

Snap Ring is a retaining ring that seats into a machined groove to locate a component on a shaft or within a bore, holding it against axial movement.

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Washer

Stud for the timing cover (front cover) of the 2.5L 4-cylinder diesel engine. The stud locates and clamps the front cover to the cylinder block, p...

Waterproof seat cover for a single outer front seat, finished in grey. The cover is shaped to the standard seat frame and fits over the existing u...

Floor Mat - Rear is a moulded rubber floor mat for the rear of the vehicle. It protects the rear floor, providing a hard-wearing, washable surface.

Fixing Plate fitted at the rear of the tailgate latch, from the tailgate assembly. The plate backs the latch mounting on the tailgate, providing t...

Rear Tailgate Side Seal Hcpu

Bulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...

Thermostat Assembly for the 2.4L Duratorq TDCi diesel, mounted in the oil cooler and filter housing. It regulates coolant flow to bring the engine...

Blanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...

Fuel Pipe Clip retains and routes fuel delivery pipework within the fuel system, holding the lines securely in their intended position. It prevent...