Genuine Land Rover Parts

Speedometer Drive Gear - 21 Teeth - Green is the drive pinion in the speedometer drive assembly located on the LT230 transfer box output housing. ...

Loadspace Mat is a fitted rubber mat for the rear loadspace floor. It protects the loadspace floor surface from wear, dirt and moisture and provid...

Secure your bonnet-mounted spare wheel with this heavy-duty retainer bracket. This ring-type spare wheel retainer ensures a stable and secure fitme...

Fuel Filter TD4

washer lock shakeproof GENUINE LR for clutch hose

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Rear Door Seal for the rear door aperture on Series III and Defender 90 and 110. The rubber seal runs around the perimeter of the rear door apertu...

Body Side Step is a folding side step for the Defender, mounting to the body sill to provide a step for vehicle entry and exit. The step folds fla...

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Split Pin for the rear tailboard lower assembly. A split pin (cotter pin) passes through a drilled clevis or retaining pin and its legs are splaye...

O-Ring for the fuel injector harness assembly on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This O-ring provides a seal within the fuel injector...

Steering Column Moulding for the Defender interior. This plastic moulding fits around the base of the steering column, providing a neat trim finis...

Upper Hinge Bolt secures the upper hinge leaf to the door pillar in the door hinge assembly. On Defender, this bolt attaches the upper rear end do...

Sliding Window Seal seals the sliding side window assembly against the surrounding rear cab body panel. It runs along the window aperture, sealing...

Land Rover 110 Front Badge - an exterior identification badge carrying the "110" model designation, finished in silver lettering on a black backgro...

Handbrake Cover - the trim cover fitted around the base of the handbrake (parking brake) lever where it mounts on the transmission tunnel. It conc...

Blanking Plug for the cylinder block. It seals a machined port in the engine casting where no sensor, sender or fitting is installed, preventing co...

Spring Clip - Steel for V8 EFI petrol engines, used in the throttle linkage and gear change mechanism. This steel spring clip provides positive re...

Front Cover Drain Plate - part of the engine front (timing) cover assembly. It closes and seals the drain aperture at the base of the front cover. ...

Camshaft Bolt for the Rover V8 engine, securing the camshaft sprocket to the front of the camshaft. This M12 x 30 mm bolt retains the camshaft dri...

Gasket

Mud Flap Bracket for the right-hand rear position on High Capacity Pick Up (HCPU) bodywork. Part of the exterior mud flap mounting. The HCPU rear ...

Truck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Heater Control Label - replacement decal for the heater control panel. Fits within the HVAC control assembly and provides the printed markings ind...

Bolt - M12 × 160 mm hex-head bolt used as a chassis and suspension fixing. It secures suspension radius arms and links, the top link fulcrum and ba...

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

TDi Decal for Defender 110. Original-specification exterior decal carrying the TDi designation. Applied to the body as part of the standard factor...

Control Unit - dim dip lighting module for the Defender electrical system. This module operates the dim dip lighting circuit, activating the headl...

Ultrasonic Alarm Sensor - the interior intrusion detector of the vehicle's anti-theft alarm system. Mounted in the cabin, it emits ultrasonic sign...

Rear Window Heated Switch

Bulb Holder A black bulb holder that retains a bulb and connects it into the lighting circuit. Used in the instrument panel and interior trim ligh...

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Multi-Height Tow Bar is a towing assembly for the high-capacity pick-up and crew cab body styles, mounting to the rear of the chassis. The multi-h...

Mainshaft for the R380 5-speed manual gearbox. The mainshaft is the central driven shaft within the R380 gearbox, carrying the output gear cluster...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Clutch Damper for the Defender Puma hydraulic clutch circuit. This in-line hydraulic damper installs within the clutch hydraulic hose run between ...

Hazard Switch Bulb Illumination bulb for the hazard warning switch within the facia switch assembly. It provides the internal lighting that illumi...

Anti-Burst Lock - right-hand tailgate latch assembly. The anti-burst design captures the striker pin within a rotating claw, holding the door close...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...