Genuine Land Rover Parts

Brake Pipe T-Piece is a three-way hydraulic union in the rear braking circuit, joining the incoming brake line to the two rigid pipes that feed the...

Pan Head Bolt, M8 x 40mm. Metric pan head bolt for use across Land Rover body, chassis, and interior assemblies.

Bulb & Holder for the instrument panel warning lights. The assembly pairs an illumination bulb with its holder, which fits into the rear of the...

Steering Box Sector Shaft for the Adwest power-steering box. The sector shaft is the output shaft of the recirculating-ball steering box. The worm...

Piston ring set petrol 2,25 020 Mahle (per zuiger)

Output Shaft Washer - LT230 Transfer Box for the Defender Puma drivetrain assembly. This washer seats behind the output shaft flange at both the f...

Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Radiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...

Gearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...

Split Pin is a cotter-type retaining pin used to lock a clevis pin or pivot pin in position. It passes through the cross-drilled end of the pin an...

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Heater Hose carries engine coolant between the cooling system and the heater matrix, forming part of the cabin heating circuit. Hot coolant is rou...

Handbrake Cable Bracket for the parking brake cable assembly. This bracket mounts to the body or chassis to guide and anchor the handbrake cable, ...

Chassis Mounting Plate is a spreader plate for the body mounting bracket, fitting at the chassis outrigger where the body is secured to the chassis...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Foam Gasket seals the door lockface, part of the door latch and lock assembly. It fits between the latch mechanism and the lockface panel, sealing...

Roof Seal Retainer is a fixing strip within the roof assembly that secures the roof weather seal, clamping the seal in place where the roof panel m...

Corner Bracket - Galvanised - LH on the rear body panel at the tailgate aperture. This galvanised steel bracket is fitted to the body on the left-...

Retainer for the carpet and seat base assembly in the Land Rover Defender. This retainer secures the floor carpet or seat base trim panel within t...

Hood Grab Handle for the soft top assembly. The handle is fitted to the soft top to provide a hand grip for occupants. It mounts to the hood frame...

Steering Column Top Clamp in the steering column mounting, securing the upper end of the steering column to its support bracket. The clamp holds t...

Door Inner Waist Seal (Front) runs along the inner waistline of the front door, sealing against the window glass. Mounted on the inboard face of t...

Bonnet Staple - the fixed engagement point within the hand-operated bonnet locking assembly. This component mounts to the bonnet panel and interfa...

Oil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...

Heater Hose - outlet pipe from the heater matrix, Td5 2.5L 5-Cylinder Turbo Diesel, left-hand drive (LHD). Returns engine coolant from the heater ...

Layshaft is the countershaft within the R380 five-speed manual gearbox, carrying the cluster of gears that mesh with the mainshaft gears. Drive pa...

Pinion Shaft for the LT77 five-speed manual gearbox. This is the primary constant pinion - the input pinion of the gearbox mainshaft assembly - wh...

Gear Change Retaining Plate for the LT77 and R380 5-speed manual gearbox. Fitted within the gearchange housing, this plate retains the gear select...

Front Brake Disc Shield - Defender This pressed-steel shield fits behind the front brake disc on the Defender, located between the disc and the sw...

Breather Assembly vents the front axle housing, letting trapped air escape and equalising internal pressure as the differential oil heats and cools...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Centre Front Seat Belt for the Defender occupant restraint system. This seat belt assembly occupies the centre front seating position and is used ...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Fuel Pipe for the 200 TDi diesel fuel delivery circuit. Connects the fuel filter outlet to the injection pump inlet, carrying filtered fuel to the...

Fuel Tank Bracket for the fuel tank mounting assembly on the Defender. This steel bracket secures the fuel tank to the chassis, forming part of th...

Engine Plug - a cylinder head core plug (welch plug) for the Td5 2.5L 5-cylinder turbo diesel engine. Core plugs seal the casting holes left in th...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Injector Spill Pipe links the fuel injectors in the 2.5L 4-cylinder turbo diesel injection system. It returns leak-off (spill) fuel from the injec...

Door Trim Panel is the interior trim panel, or door card, fitted to the inner face of the door. It forms the finished interior surface and conceals...