Genuine Land Rover Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

24v dsl long belt

Heated Windscreen Push Switch is the facia-mounted control switch for the heated front windscreen circuit. Pressing the switch energises the heati...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Outside door release cable handle to latch RH/LH

Floor Mat Set is a set of tailored rubber floor mats that protect the cabin footwells from mud, water and everyday wear. The moulded rubber constr...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Wiper Switch Assembly

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Windscreen Wiper

Rear Wiper Motor for the tailgate wash/wipe system. It mounts at the rear of the vehicle and drives the rear wiper arm and blade across the rear sc...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Wiper Arm is the windscreen wiper arm that carries the wiper blade across the windscreen. It mounts to the wiper linkage spindle and transfers the...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Tube - Water Outlet

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Fuel Filter TD4

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Kit - Boot

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Rear Window Heated Switch

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

EGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...

Leak-Off Tube - Injection Pump

Oil Separator is part of the crankcase ventilation system on the 2.7L V6 Lion diesel engine. It separates oil mist from the crankcase blow-by gase...

Exhaust Gas Temperature Sensor measures exhaust gas temperature at the front of the diesel particulate filter, in the upstream section of the after...

Housing thermostat GENUINE ROVER

Dual Note Horn - the audible warning horn assembly, part of the electrical system, supplied as a matched pair on a common mounting bracket. The se...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...