Genuine Land Rover Parts

Bolt Mounting bolt for the power steering pump and front cover housing, and for air conditioning compressor and condenser mountings.

Shield - Water Splash

Sunroof Water Drain Tube for the power tilt-and-slide sunroof drainage system. It routes water collected in the sunroof cassette drain channel down...

Stud

Self-Tapping Screw - a fastener that cuts its own thread as it is driven, used in the luggage compartment door finisher and trim assembly. It secu...

Bumper Retainer A quarter-turn click-type fastener that secures the bumper and radiator grille panels to the body. It locates through the mounting ...

Clip retaining rear body mouldings to the body, including the rear wheel arch moulding and front door cladding. A push-in plastic clip; sold indiv...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Wiper Arm Cap is the spindle nut cover that fits over the wiper arm pivot, concealing and protecting the retaining nut where the arm mounts to the ...

Rear Wiper Blade is the wiping element for the rear wash/wipe system, mounted on the tailgate wiper arm. It clears rain and road spray from the re...

Door Moulding is the protective trim that fits along the lower outer edge of the front door on the right-hand side. It shields the bottom of the d...

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Name Plate - "ROVER" is a bonnet name badge carrying the "ROVER" lettering in a Brunel Metallic finish. It fixes to the bonnet as the second half ...

Name Plate - "LAND" is a bonnet name badge carrying the "LAND" lettering in a Brunel Metallic finish. It fixes to the bonnet as the front half of ...

Door Handle Cover that caps the exterior door handle at the door lock control, finishing the handle assembly. Supplied in black, this is the blank...

Mud Flap Set - Rear shields the rear bodywork and lower panels from stones, mud and road debris thrown up by the rear wheels. Supplied as a matche...

Fuel Filler Door Seal is the rubber seal fitted around the fuel filler door aperture in the rear body panel. It seals the recess behind the hinged...

Fuel Filler Door Spring for the fuel filler door and controls assembly. This spring provides the return force that holds the fuel filler door in t...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Fuel Filler Door Actuator operates the fuel tank filler flap as part of the central locking system. The actuator drives the locking pin that secur...

Door Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...

Bracket - Fender Mounting

Fuel Filler Door Latch Bezel is the trim surround that locates and frames the fuel filler flap latch within the fuel filler housing. It seats in t...

Floor Pan Blanking Plug. It closes an unused aperture in the floor pan, sealing the opening against water, dust and road debris.

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Cylinder Head Bolt - M10 x 175mm bolt clamping the cylinder head to the block on the AJ-series V8 petrol engine. A torque-to-yield fastener; twent...

Oil Filter filters the engine lubrication oil on the 4.0L V6 Cologne SOHC petrol engine, removing contaminants from the oil before it returns to th...

Timing Chain Tensioner – Balance Shaft maintains tension on the balance shaft drive chain of the 4.0L V6 Cologne SOHC petrol engine, taking up slac...

Tube - Injection Pump Leak-Off

Gasket - Oil Tube

Engine Oil Sump for the 2.7 TDV6 diesel engine. The sump forms the lower section of the crankcase and houses the oil reservoir from which the oil p...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Glow Plug for the TDV6 2.7L and TDV8 3.6L diesel engines. Glow plugs are installed per cylinder in the cylinder head and heat the combustion chamb...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Thermostat Housing Gasket for the 2.7L TDV6 diesel engine. This gasket seals the thermostat housing (water outlet) to the engine, preventing coola...

Oil Separator Seal - sealing gasket for the oil separator in the crankcase ventilation system of the 2.7 and 3.0 litre V6 diesel engines. The oil ...

Thermostat O-Ring for the TDV6 diesel engine. This O-ring provides the coolant seal at the thermostat housing on TDV6 diesel engines, preventing c...

EGR Outlet Pipe Gasket seals the joint between the EGR outlet pipe and the intake system on the 2.7L TDV6 diesel engine (Lion V6). It sits where r...

Exhaust Gasket for the TDV6 2.7L V6 diesel engine. Seals the joint between the exhaust manifold and the cylinder head, preventing exhaust gas leaka...