Genuine Land Rover Parts

24v dsl long belt

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Leak-Off Tube - Injection Pump

Turbocharger for the 2.0L AJ200 / AJ20D4 four-cylinder diesel engine. It sits in the forced-induction circuit between the exhaust manifold and the...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Front Driveshaft, Left-Hand transmits drive from the front differential to the left front wheel hub within the front axle assembly. Constant-veloc...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Washer - Sealing

Bolt

Rear brake disc, 365mm diameter, forming part of the rear brake disc and caliper assembly. The disc bolts to the rear hub flange and provides the ...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Bolt - hex-head bolt with washer, used in the splash and heat shield assembly. It secures the underbody splash shields and powertrain undertray pa...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Intercooler (charge air cooler) for the turbocharger induction circuit, mounted at the front of the vehicle within the cooling pack airflow. Compr...

Rear Exhaust Damping Mass - tuned mass damper for the rear section of the exhaust system. The damper clamps to the rear exhaust pipework and adds ...

Exhaust Gas Pressure Sensor for the 2.0L AJ200D Ingenium four-cylinder diesel, working within the turbocharger and exhaust gas management circuit. ...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Parking Camera for the surround camera system. The camera supplies a video feed to the vehicle's parking and surround-view display, assisting with...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Exhaust Pipe Gasket seals the front flanged joint of the exhaust system, maintaining a gas-tight connection and preventing exhaust leakage at the j...

O-Ring is a sealing ring used in the Exhaust Gas Recirculation (EGR) circuit of the 2.0L four-cylinder AJ200 diesel engine. It seals a joint in th...

Intercooler Pipe connecting the turbocharger outlet to the intercooler in the charge-air system of the 2.0L AJ200 (Ingenium) four-cylinder diesel e...

EGR Valve Gasket seals the exhaust gas recirculation valve to its mating face within the EGR and front exhaust system. Fitted on the left-hand ban...

Manifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine, mounted in the throttle housing. It measures absolute pressure in the intake...

Fuel Pump Drive Belt Kit for the rear accessory drive of the 3.0L V6 diesel engine. The belt transmits drive to the high-pressure fuel injection p...

Climate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Front Brake Disc for the front axle, matched to the size-19 front brake configuration. It mounts to the front wheel hub and rotates with the wheel...

EGR Gasket Inlet

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...