Genuine Land Rover Parts

Washer Bottle Filler Cap - the filler cap for the windscreen washer fluid reservoir. It closes the reservoir filler neck, sealing the washer fluid...

Grommet - a moulded rubber grommet fitted into an aperture in the body. It lines and seals the opening, providing a finished edge and helping to k...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Pin is a push-in retaining clip for exterior body trim. It secures side trim panels and body mouldings to the body, holding the trim seated at its...

Sealing Ring - the right-hand outer seal for the front axle case, part of the front driveline. It seals the point where the front driveshaft passe...

Air Conditioning O-Ring - a sealing ring for the air conditioning refrigerant circuit. It seals the joints between refrigerant lines and component...

O-Ring - 15 x 3mm sealing ring used on the 3.2L DOHC petrol inline-six engine. It seals within the oil cooler and filter assembly and in the cooli...

Oil Cooler Inlet Tube - rigid oil feed tube within the oil cooler and filter assembly on the 3.2L DOHC MPI petrol inline-six. The tube carries eng...

Cylinder Block Front Cover - crankshaft front cover for the cylinder block on the 3.2L DOHC MPI petrol inline-six. The cover closes off the front ...

Fuel Filter - diesel fuel filter for the 2.2L Td4 engine, fitted in the low-pressure fuel supply circuit. The filter sits between the fuel tank an...

Thermostat Housing - coolant outlet housing in the engine cooling circuit of the 2.2L Td4 diesel engine. The housing mounts to the engine and carr...

Oil Filter - engine oil filter element for the 2.2L Td4 diesel engine, supplied with its sealing ring. The element fits inside the filter housing ...

Parking brake operating lever (shoe expander) for the rear drum-in-disc parking brake assembly. The lever is mounted to the parking brake shoe and...

EGR Cooler for the 2.2L DOHC DW12 turbo diesel engine, part of the exhaust gas recirculation circuit. The cooler is a coolant-fed heat exchanger: ...

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Coolant Hose between the radiator and the coolant expansion tank. This is the overflow connection of the cooling system: coolant displaced from th...

Coolant Hose from the EGR cooler to the heater inlet, part of the engine cooling and exhaust gas recirculation circuit. The EGR cooler is coolant-...

Coolant Hose Assembly - heater outlet to thermostat housing hose in the engine cooling circuit. Returns coolant from the heater matrix outlet to t...

Coolant Hose - bottom expansion tank hose in the engine cooling circuit. Runs from the lower outlet of the coolant expansion (supply) tank to the ...

Radiator Hose - upper radiator hose in the engine cooling circuit. Connects the engine coolant outlet to the top inlet of the radiator, forming th...

Sealing Ring - oil seal at the input of the AWF21 six-speed automatic transmission, sealing around the torque converter hub where it enters the tra...

Indicator Bulb - PY21W amber signal bulb, 12V 21W, fitted to the direction indicator lamp units. The amber envelope provides the signal colour req...

Anti-Roll Bar Bush for the suspension stabiliser system. This rubber insulator clamps the anti-roll bar to its mounting, locating the bar while all...

Sump Plug Washer for the 3.2L DOHC MPI petrol inline-six engine. This sealing washer fits under the sump drain plug to seal the oil pan drain threa...

Hex-Head Bolt and Washer - bolt and washer assembly used in the front suspension and subframe area. The fastener secures front cross member, stabi...

Radiator Cap - screw-on pressure cap for the coolant expansion tank in the engine cooling system. The cap seals the expansion tank and holds the c...

Bolt - M10 x 25 mm, with washer. Underbody and chassis fixing used to secure engine splash shields, heat shields and underbody protection panels t...

Seat Back Adjustment Handle - the operating handle for the front seat backrest recline mechanism, mounted on the outboard side of the seat frame. ...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Bolt Mounting bolt for the power steering pump and front cover housing, and for air conditioning compressor and condenser mountings.

Stud

Bumper Retainer A quarter-turn click-type fastener that secures the bumper and radiator grille panels to the body. It locates through the mounting ...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Clip for the headlamp washer system. Retains the headlamp washer jet to the bumper.

Door Handle Cover that caps the exterior door handle at the door lock control, finishing the handle assembly. Supplied in black, this is the blank...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Air Filter is the air cleaner filter element for the engine intake system. It sits within the air cleaner housing upstream of the intake tract, re...

Bolt - Hexagon Head used in engine and interior fascia assembly applications. This hexagon head fastener is used in the EGR system assembly and in...

Control Switch Assembly