Genuine Land Rover Parts

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Handbrake cover LHD

Strap

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Front Brake Anchor Plate (back plate) for the right-hand side, part of the front drum brake assembly. The anchor plate bolts to the axle and carri...

Brake Pipe Clip - Rear secures the rear brake pipes on the Discovery 2, holding the hydraulic lines in place along the chassis. The clip prevents ...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Brake pipe clip

Distance piece

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Handbrake Cover - the trim cover fitted around the base of the handbrake (parking brake) lever where it mounts on the transmission tunnel. It conc...

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Caliper Repair Kit - Front - Axle Set

Brake Pipe T-Piece is a three-way hydraulic union in the rear braking circuit, joining the incoming brake line to the two rigid pipes that feed the...

Pressure Seal

Handbrake Carrier Spacer for the handbrake assembly on Series II, IIA, III and Defender 90/110. This spacer fits within the handbrake carrier mech...

Handbrake Cable Bracket for the parking brake cable assembly. This bracket mounts to the body or chassis to guide and anchor the handbrake cable, ...

Handbrake Gaiter for the handbrake lever assembly in Series II, IIA, and III Land Rovers. Fits 109-inch wheelbase V8-engined variants. The gaiter ...

Front Brake Disc Shield - Defender This pressed-steel shield fits behind the front brake disc on the Defender, located between the disc and the sw...

Handbrake Gaiter in Dark Granite, part of the centre console trim. This gaiter fits around the base of the handbrake lever, concealing the lever me...

Front Brake Pipe - Right-Hand - short rigid steel brake pipe forming the secondary link between the chassis-mounted flexible hose and the front rig...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Brake Pad Set - Front - 18/19 Inch - friction pads for the front disc brake caliper assembly used with the larger front brake installation fitted b...

Brake Pipe Clip secures and routes rigid brake pipe runs within the braking system, holding the pipe against the chassis or body to maintain its ro...

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Handbrake Operating Lever from the parking brake control assembly. The lever is the driver-operated arm that applies the transmission brake through...

Brake Pipe Clip is a retaining clip from the front brake line mounting hardware. The double form holds two rigid brake pipes side by side at a fix...

Handbrake Shoe Set for the mechanical parking brake, which operates inside its own dedicated drum and is independent of the hydraulic service brake...

Disc - Brake

Disc - Brake

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Seal

Rear Brake Disc, 325 mm diameter, part of the rear service brake assembly. Supplied singly. The disc mounts to the rear wheel hub and provides the...

Kit - Caliper Brake Pad

Rear brake disc, 365mm diameter, forming part of the rear brake disc and caliper assembly. The disc bolts to the rear hub flange and provides the ...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Front Brake Hose - the flexible hydraulic hose in the front brake circuit, connecting the rigid brake pipe on the body to the caliper at the hub. ...

Wire - Brake Pad Wear Warning