Genuine Land Rover Parts

Window switch

EDC switch Puma

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Windscreen Wiper Wheelbox Spindle Housing for the windscreen wiper rack mechanism. The unit mounts through the bulkhead or scuttle panel and suppo...

Heated Windscreen Push Switch is the facia-mounted control switch for the heated front windscreen circuit. Pressing the switch energises the heati...

Heater Control Bulb illuminates the heater and ventilation control panel. Fitted into the front HVAC control assembly, it backlights the heater co...

Flasher Lamp Lens - Sparto Type is the replaceable coloured lens for the Sparto-pattern direction indicator (flasher) lamp, forming part of the ext...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Aerial – Front Wing is the wing-top radio antenna for the vehicle audio system. The all-metal telescopic mast mounts to the top of the front wing ...

Rear Fog Lamp Switch is the dashboard-mounted control for the rear fog lamp circuit. This switch allows the driver to activate the rear fog lamp f...

Dial Illumination Bulb for the climate control panel, providing backlighting for the heating and ventilation controls. It seats behind the switch ...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Amber Switch Bulb for the heated windscreen and auxiliary switches. This small bulb provides the amber illumination within the switch, lighting th...

Switch

Headlamp Gasket for the headlamp mounting assembly. A rubber seal that fits between the headlamp unit and the surrounding body panel, providing a ...

Front Screen Timer Relay is the grey timer relay within the heated front windscreen circuit. When the heated screen is switched on, this relay ene...

Pump Injection Ring

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Single-Pole Bulb Holder fitted within the rear lamp assembly, providing the electrical interface and physical retention for the stop or tail lamp b...

Rear Lamp Bulb Holder Double-pole bulb holder that seats in the rear lamp housing, retaining the bulb and carrying the electrical contacts between ...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Interior Lamp Lens for the interior courtesy lamp. The translucent lens clips over the lamp body, protecting the bulb and diffusing its light into...

Instrument Bulb Holder Assembly is a 1.4W instrument panel bulb supplied complete with its integrated holder, forming part of the instrument cluste...

Wiper Switch Assembly

Fuse - 100A high-current rated fuse for the main electrical protection circuit. Rated at 100 amps, this fuse protects the highest-current circuits...

Door Speaker An original-fit speaker for the in-car audio system. It reproduces the audio output of the radio/head unit through the vehicle's spea...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

Cigar Lighter Mounting Plate, the fascia panel that carries the cigar lighter unit. It mounts into the dashboard fascia, locating and retaining th...

Dial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Screw for securing the rear reflector, fog lamp, and reverse lamp assembly on the Land Rover Defender. Used to retain the lamp cluster components ...

Remote Handset Case - replacement housing for the remote locking plip (key fob), supplied as the case only without the internal electronics. House...

Headlamp Bulb Cover for the front headlamp assembly. This rubber cover seals the bulb access aperture at the rear of the headlamp unit following b...

Hexagon Nut for use in electrical system assemblies.

Battery Fixing Stud - Long Straight is a long straight J-bolt used to secure the battery retaining clamp to the battery tray. The stud passes thro...

Clip is a locking retaining clip in the front windscreen wiper linkage. It locks the wiper linkage connection, securing the motor and linkage asse...

Rear Wiper Motor for the tailgate wash/wipe system. It mounts at the rear of the vehicle and drives the rear wiper arm and blade across the rear sc...

Double Clip for routing and securing battery cables. This twin clip retains two leads together, holding the cabling in place along its run.

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Bulb & Holder - Main Instrument Panel for the Discovery 2 instrument cluster illumination circuit. This bulb and holder assembly fits into the...

Wiper Blades - Front Pair is a replacement windscreen wiper blade set, supplied as a matched front pair for right-hand drive configurations. The bl...