Genuine Land Rover Parts

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Escutcheon Seal for the exterior door handle escutcheon. The seal sits between the handle escutcheon and the outer door skin, sealing the aperture...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Pipe seal

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Door Latch Linkage Clip for the door latch and lock assembly. It retains the operating rod on the latch mechanism. The clip holds the handle-to-la...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Level plug R380

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Windscreen Wiper Wheelbox Spindle Housing for the windscreen wiper rack mechanism. The unit mounts through the bulkhead or scuttle panel and suppo...

Split Pin used to secure the accelerator cable and hand throttle cable connections, retaining the clevis pin at the cable-to-linkage joint. After ...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...

Cylinder Head Bolt clamps the cylinder head to the cylinder block on the diesel engine, compressing the head gasket to seal the combustion chambers...

double washer, restrictor

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 3-1/4" shank length. This long-shank bolt is used at the alternator mounting on...

Brake Pipe Clip - a single moulded plastic clip that secures a brake pipe to the chassis within the braking hydraulic circuit. It retains the rigi...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

O-ring

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Oil Pump Sealing Washer, part of the engine lubrication circuit at the oil pump. The washer forms a static seal at the oil pump joint, preventing ...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Clevis Pin for the front door hinge and check strap assembly. This pin secures the door check strap (travel limiter) at its pivot, retaining the s...

A-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...

Spring Washer is an M8 double-coil spring washer used as a fastening component in body and chassis assemblies. The double-coil spring form maintai...

Driveshaft Spacer - a 15.5mm spacer used within the front and rear axle drive shaft and hub assembly. The spacer sits between the drive shaft and ...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Escutcheon

Door Latch Link Clip secures the operating link rod within the door latch and locking assembly. It retains the connecting linkage that transfers m...

Plenum to Water Jacket Gasket seals the joint between the plenum chamber and the water-jacketed intake manifold in the Rover V8 EFI induction syste...

O-Ring for the air conditioning hose circuit. This O-ring seals connections within the air conditioning pipework, preventing refrigerant loss at p...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Exhaust manifold stud