Genuine Land Rover Parts

Torx Flanged Screw - Front Door Latch Assembly for the front door latch mechanism. This Torx-head flanged screw secures the front door latch assem...

Layshaft is the countershaft within the R380 five-speed manual gearbox, carrying the cluster of gears that mesh with the mainshaft gears. Drive pa...

Pinion Shaft for the LT77 five-speed manual gearbox. This is the primary constant pinion - the input pinion of the gearbox mainshaft assembly - wh...

Gear Change Retaining Plate for the LT77 and R380 5-speed manual gearbox. Fitted within the gearchange housing, this plate retains the gear select...

Front Brake Disc Shield - Defender This pressed-steel shield fits behind the front brake disc on the Defender, located between the disc and the sw...

Oil Seal Retainer for the front axle. It retains the oil seal at the swivel pin bearing housing, holding the seal that runs against the halfshaft.

Breather Assembly vents the front axle housing, letting trapped air escape and equalising internal pressure as the differential oil heats and cools...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Tailgate Latch Assembly is the lower tailgate latch mechanism, fitted at the centre of the lower tailgate. It secures the lower tailgate closed an...

Handbrake Gaiter in Dark Granite, part of the centre console trim. This gaiter fits around the base of the handbrake lever, concealing the lever me...

Centre Front Seat Belt for the Defender occupant restraint system. This seat belt assembly occupies the centre front seating position and is used ...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Fuel Pipe for the 200 TDi diesel fuel delivery circuit. Connects the fuel filter outlet to the injection pump inlet, carrying filtered fuel to the...

Fuel Tank Bracket for the fuel tank mounting assembly on the Defender. This steel bracket secures the fuel tank to the chassis, forming part of th...

Engine Plug - a cylinder head core plug (welch plug) for the Td5 2.5L 5-cylinder turbo diesel engine. Core plugs seal the casting holes left in th...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Injector Spill Pipe links the fuel injectors in the 2.5L 4-cylinder turbo diesel injection system. It returns leak-off (spill) fuel from the injec...

Plenum Hose is a moulded hose serving the plenum chamber of the V8 EFI petrol induction system. It forms part of the plenum chamber assembly on th...

Door Trim Panel is the interior trim panel, or door card, fitted to the inner face of the door. It forms the finished interior surface and conceals...

Sunroof Finisher - perimeter seal trim section for the manual slide sunroof assembly on the Discovery II. The component forms the finishing strip ...

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Grille is the front-face grille panel for the Discovery 1, fitted to the nose of the vehicle between the headlamps and above the front bumper. Thi...

Clutch Pedal Spring Bush is a small bush fitted to the clutch pedal assembly on the Defender 90/110, locating the pedal return spring. The bush se...

Module - relay and diode pack serving the fuel injection electrical circuit. It controls and protects the power supply feeding the electronic petro...

ROVER Lettering Emblem - silver, 35 cm - for Defender (2007-2016). This is the adhesive silver lettering strip that spells out "ROVER" on the exte...

Emblem - LAND - Silver - 28cm is the "LAND" lettering badge that forms part of the bonnet exterior script. The silver badge measures 28 cm in leng...

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Door Latch Stud Plate for the front door latch mechanism. The striker stud plate mounts to the body pillar and provides the fixed engagement point...

Torx Bolt from the Land Rover fixings and fasteners range. A Torx-drive bolt for use in Land Rover assembly applications requiring a Torx head fix...

Tailgate Transfer Decal - "TDi" Badge for the Discovery 1 body graphics assembly. This self-adhesive transfer decal carries the "TDi" engine desig...

Heater Hose - Heater Matrix to Control Valve forming part of the engine cooling and cabin heating circuit. This hose runs between the heater matri...

Decal - Bonnet - Basalt Edition for the Range Rover P38. This is the bonnet decal specific to the Range Rover P38 Basalt special edition. It repli...

Electric Exterior Mirror left-hand door mirror assembly with electrically adjustable glass. Mounts to the exterior door and provides the driver's ...

Plastic Rivet for use in the rear bumper assembly on Discovery 1. This plastic push-fit rivet secures bumper trim and moulding panels to their mou...

Body Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...