Genuine Land Rover Parts

Self-Tapping Screw, No.6 x 3/8". A self-tapping fastener that forms its own thread as it is driven, used to secure body panels, trim and light fix...

Front Radius Arm Washer - plain flat washer used at the inner bushing position of the front radius arm on the Range Rover P38, installed between th...

Clip - a small retaining clip used within the transfer box differential lock linkage and at the handbrake lever and clutch master cylinder mounting...

Front Brake Pipe - Right-Hand - short rigid steel brake pipe forming the secondary link between the chassis-mounted flexible hose and the front rig...

Rear Fog Switch for the dashboard switching circuit. A push-push type switch that controls activation of the rear fog lamp circuit. Mounts in the ...

Rear Wiper Arm forms part of the rear screen (backlight) wiper assembly. It mounts onto the rear wiper motor spindle and carries the wiper blade a...

Headlamp Wash Pump is the electric motor and pump unit that pressurises the headlamp washer system on the Discovery 1. The pump draws from the win...

Door Lock Actuator Electric actuator in the central door locking system. Mounted within the door, it drives the latch to the locked and unlocked p...

U-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Facia Assembly Fastener - a fastener for mounting the facia assembly to the dash structure. It secures the facia panel in place and is also used t...

Starter Motor Brush Kit for the Lucas M113-type starter motor in the engine starting system. The brushes bear on the armature commutator to transf...

Heater Control Cable - Heat Outlet for Defender 90 and 110 vehicles. This Bowden cable connects the heat outlet control lever on the heater contro...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Snap Ring

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Bush

Upper Tailgate Screw, a fixing used in the upper tailgate assembly. It secures the upper tailgate components in place, providing a threaded fasten...

Retaining Clip used to hold the lock barrel in place. Supplied as a single clip.

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Primary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...

Inner Ring

Stud for the carburettor-to-inlet-manifold joint. Threaded stud that secures the carburettor onto the inlet manifold flange. It provides the fixin...

Washer 577254

Heater Control Pin

Temperature Sensor Adaptor - UNF-threaded adaptor for the water temperature transmitter. Screws into the engine coolant passage to accept the temp...

rod control GENUINE LR - 2.25 petrol and 2.6 petrol, 1968 onwards

Bush - Low Gear Wheel is a gearbox internal bush fitted to the low gear wheel in the Series 2 and Series 3 manual gearbox on 109-inch 1-ton Land Ro...

Slip Ring for the horn contact in the steering column. This contact ring maintains the electrical connection to the horn as the steering wheel tur...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Screw - a threaded fastener used to join or secure components.

Harness Bracket Shim for the wiring harness mounting hardware. Fitted behind the harness support bracket at its mounting point, the shim sets the ...

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Rear Window Sealing Pad for the Range Rover Classic. This rubber pad seals the rear side window aperture, preventing water ingress and wind noise ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Steering Column Top Clamp secures the upper section of the steering column at its top support within the steering column assembly. It clamps the c...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Washer

Top cover

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Brush kit RTC830 fits: Rover 3.5L V8 startermotor type 3M100 - S3 109" stage 1 V8 - 101" Forward Control - Range Rover Classic

Locking Wheel Nut Cap in stainless steel, fitting over the exposed end of a locking (anti-theft) road wheel nut. The cap conceals and protects the...

Hex Nut

Differential Thrust Washer Thrust washer for the differential gears within the Salisbury rear axle. It seats behind a differential gear in the fou...