Genuine Land Rover Parts

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Speedometer for the instrument pack, calibrated to Japan-market specification for the 4.0L V8 EFi petrol engine with automatic transmission. Mount...

Front Fog Lamp is the right-hand front fog lamp assembly within the exterior front lighting system. Mounted in the right-hand side of the front bu...

Speaker Bezel is the trim surround that frames a speaker opening in the interior. Part of the in-car entertainment (ICE) installation, it finishes...

Door Lock Actuator Electric actuator in the central door locking system. Mounted within the door, it drives the latch to the locked and unlocked p...

Sealing Washer, a 14mm aluminium crush washer for the sump (oil pan) drain plug, forming the drain-seal element of the engine lubrication system. ...

Bonnet Release Cable, part of the bonnet latch and release mechanism. The cable connects the interior release lever to the bonnet lock, transmitti...

Door Release Cable - Front - LH Internal release cable in the front door latch mechanism. It connects the interior door release lever to the door ...

Front Door Outer Waist Seal fitted along the upper edge of the front door outer panel, sealing the interface between the outer panel and the door d...

Bar - Torsion

Floor Pan Blanking Plug. It closes an unused aperture in the floor pan, sealing the opening against water, dust and road debris.

Rear Lower Wheelarch is a body panel forming the lower section of the rear wheelarch on the 110" wheelbase Station Wagon bodyshell. It defines the ...

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Screw - a threaded fastener used across several exterior body fixings. It secures fittings within the radiator grille, the rear end door seals and...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Rear Brake Pad Kit - a complete set of disc brake pads for the rear axle, fitted to the rear brake calipers. The pads clamp against the rear brake...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Radiator Mounting Bush is the rubber isolation bush that secures the radiator to the body or chassis mounting points, preventing direct metal-to-me...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Ignition Coil for the AJ-V8 petrol engine. This coil is of the coil-on-plug type, fitted one per cylinder, mounting directly over the spark plug to...

Grommet - Valve Cover

Valve Cover Grommet for the AJ-V8 petrol engine. It seals the cylinder head (valve) cover where a component passes through it, preventing oil escap...