Genuine Land Rover Parts

Clutch Plate & Cover Assembly forms the driven and clamping elements of the clutch, sitting between the engine flywheel and the gearbox input s...

Flanged Nut for use in Land Rover assembly applications. The integrated flange acts as a built-in load-spreading face, distributing clamping force ...

Centre Floor Heelboard Carpet - left-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the ...

Centre Floor Heelboard Carpet - right-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the...

"Td5" Badge - engine-designation badge identifying the Td5 diesel engine variant. Applied to the exterior body as an engine identifier.

Cooling Fan Nut for the V8 petrol engine. The nut secures the viscous fan coupling to the water pump drive spindle, retaining the engine cooling f...

Intake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...

Latch - Tailgate

Snap Ring is a retaining ring that seats into a machined groove to locate a component on a shaft or within a bore, holding it against axial movement.

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Screw for the valve rocker (rocker shaft) assembly of the VM 2.4L and 2.5L 4-cylinder turbo diesel engine. Retains the rocker gear on the cylinder...

Front Bumper - complete front bumper assembly supplied with the integrated radiator grille section. The bumper mounts across the front of the body...

Bumper Mounting Bracket supports the front bumper, within the radiator grille and front bumper assembly. It locates and secures the bumper cover t...

Battery Cover Frame - Top is the upper frame section of the battery cover assembly. It forms the top of the battery enclosure, locating and retain...

Vacuum Hose and Valve assembly for the brake servo (booster) vacuum circuit, connecting the engine vacuum pump to the servo inlet. Hose and valve a...

Housing Rear Axle Lion Diesel 2.7 V6

Control Switch Assembly

Wiring Harness Set is the main electrical loom that carries power and signal connections through the vehicle's electrical system, tying the chargin...

Washer

Tailgate Seal for the luggage compartment door. This rubber seal runs around the tailgate aperture, weatherproofing the join between the door and t...

Stud for the timing cover (front cover) of the 2.5L 4-cylinder diesel engine. The stud locates and clamps the front cover to the cylinder block, p...

Sunroof Panel Opening Seal seals the sliding roof panel against the roof aperture. Fitted around the opening of the power tilt/slide sunroof, it f...

Door - Front - LH is the left-hand front door, the hinged body closure for the front door opening. It hangs from the body on the front door hinges...

Seat Belt and Retractor assembly for the occupant restraint system. It combines the seat belt webbing with the inertia-reel retractor, which permit...

Adhesive Tape applied to the left-hand rear quarter panel as an exterior body trim graphic. The tape is a dark grey self-adhesive panel strip fitt...

Power Steering Hose forms the low-pressure feed line of the power steering hydraulic circuit, carrying fluid from the reservoir to the inlet of the...

Waterproof seat cover for a single outer front seat, finished in grey. The cover is shaped to the standard seat frame and fits over the existing u...

Rear Seat Back Adjusting Handle - the release lever on the rear seat frame assembly. The handle operates the seat back latch, releasing the backre...

Coolant Pipe O-Ring for the Td4 2.0L M47 four-cylinder diesel engine cooling circuit. This O-ring seals the coolant pipe connection at the coolant...

Floor Mat - Rear is a moulded rubber floor mat for the rear of the vehicle. It protects the rear floor, providing a hard-wearing, washable surface.

High-Level Stop Lamp - the centre high-mounted stop lamp (CHMSL), positioned above the rear screen. It operates with the brake lighting circuit to...

Fixing Plate fitted at the rear of the tailgate latch, from the tailgate assembly. The plate backs the latch mounting on the tailgate, providing t...

Rear Tailgate Side Seal Hcpu

Bulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...

Cable Assembly

Thermostat Assembly for the 2.4L Duratorq TDCi diesel, mounted in the oil cooler and filter housing. It regulates coolant flow to bring the engine...

Front Flasher Bulb for the front direction indicator lamp, wedge base. The bulb provides the front turn-signal (flasher) illumination.

Blanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...

Fuel Pipe Clip retains and routes fuel delivery pipework within the fuel system, holding the lines securely in their intended position. It prevent...

Gearbox Selector Mount - a rubber mounting in the gearbox gear-change assembly. The rubber locates and isolates the selector mechanism, absorbing ...

Sealing Washer for the front propshaft to IRD (Intermediate Reduction Drive) unit joint. The washer sits at the bolted flange where the front prop...